Vol 22, No 6 (2024)

December

DOI: http://dx.doi.org/10.30811/jpl.v22i6

Table of Contents

Structural failure study of truck rear wheel drive axle with defect variation using finite element method
Husaini Husaini, Ulil Rizki, Nurdin Ali
PDF
565-569
Buck boost converter control to accelerate cooling in hydrogen system coolers
Wasis Waskito Adi, Novan Akhiriyanto, Adi Alson, Yohanes Gunawan, Alfin Sahrin, Erna Utami
PDF
570-575
Pre-design of bottom ash cooling using CFD simulation: a case study of the coal generator power plant in the PT. BEST Tanjung Enim of South Sumatera
Ozkar F. Homzah, Ella Sundari, Muhammad Irfan Dzaky, Firdaus ., Fatahul Arifin, Damar Adji Prayoga, Kabul Andi Setiyadi, Kabul Kabul
PDF
576-580
Material and process parameter optimization for dimensional accuracy in Fused Deposition Modeling 3D printing
Rizqi Ilmal Yaqin, Juniawan Preston Siahaan, Mula Tumpu, Bagas Prakoso, Ade Hermawan, Febi Luthfiani, Barokah Barokah, Ahmad Kurniawan
PDF
581-589
Optimizing LNG efficiency by implementing reliquefaction technology to reduce boil-off gas and enhance profitability
M. Zaky Muhtadi, Ichsan Rayazen, Andian Ari Istiningrum, Bambang Sugito
PDF
594-599
Experimental study on the performance of Peltier TEC12706 as a cooling and heating media
Sujono Sujono, Hernawan Novianto
PDF
600-604
Modeling the effect of bullet velocity and composite fiber orientation on the ballistic impact strength of Eglass/isophthalic polyester composites
Fariz Rifqi Zul Fahmi, Harry Hermawan, Fuad Dwi Hanggara
PDF
605-611
Ergonomic working posture analysis on highway construction work using the OWAS method
Muhammad Arif Munanda, Mohd. Iqbal, M. Dirhamsyah
PDF
612-619
Kinetics of transesterifying multifeedstock oil into biodiesel
Haris Numan Aulia
PDF
620-624
Fuzzy logic-PLC-based controller for water treatment simulator system
Astrie Kusuma Dewi, Gilbert Labatar, Chalidia Nurin Hamdani, Asepta Surya Wardhana
PDF
625-631
Interfacial stress distribution analysis of natural fiberreinforced epoxy composites: a finite element approach
Ikramullah Ikramullah, Reja Gapatra, Seprian Haris Ananda, Rudi Kurniawan, Syarizal Fonna, Samsul Rizal, Syifaul Huzni
PDF
632-637
Numerical study on the effect of box and polygon geometry in fin and tube heat exchanger on fluid flow and heat transfer
Agung Nugroho, Muhammad Safi'i, Bukhori Putra Romadhon, Muhammad Abdul Wahid, Muhammad Edi Pujianto
PDF
638-645
Harnessing Light-Emitting Diode technology for cutting-edge Photovoltaic module characterisation
Ira Devi Sara, Fikrel Jasman, Hafidh Hafidh, Amir Zaki Mubarak
PDF
646-653
Cascade flow rate-temperature control system design based on PID controller using direct synthesis tuning method
Mochamad Rizky Pradana, Deni Aristoni, Roni Heru Triyanto, Umi Yuliatin, Suka Handaja Budi
PDF
654-661
Heat distribution analysis of cartridge heater in core and cavity of compression mold for bio-composite roof tile fabrication
Muslimin Al Masta, Maulidya Rahman, Dhiya Luqyana, Azam Milah Muhamad
PDF
662-665
The effect of TIG welding technology parameters on the weld quality of copper material joints for heat pipe applications
Azwinur Azwinur, M. Hadi Kusuma, Usman Usman, Surya Dharma
PDF
666-671
Hydroxyapatite-reinforced Al-Mg composites for corrosion resistance in hanks' balanced salt solution
zuliantoni zuliantoni, W. Suprapto, P.H. Setyarini, F. Gapsari
PDF
672-680
Analysis of worker posture of Make-Up Artist by Standard Nordic Questionnaire method and Rapid Entire Assessment
Cut Lirma Saputri Asda, Iskandar Hasanuddin, Husni Husni, Teuku Firsa
PDF
681-685
Development of Portable Pico Hydro Power Plant for Low Head Applications Using Cross-Flow Turbine
Budi Triyono, Dibyo Setiawan, Haryadi Haryadi, Vicky Wuwung, Zaki Odang, Norhafizan Ahmad
PDF
686-692
Real-Time Identification of Yarn Irregularities on DTY Machine Through Vibration Monitoring
Deni Kurnia, Agus Sutanto, Hanif Fakhrurroja, Nanang Roni Wibowo
PDF
693-698
Performance Analysis of a 2-Liter Solar Cooker with Comparison of Aluminum and Stainless Steel Containers
siwan edi amanta Perangin angin, Richard Napitupulu
PDF
699-705