Vol 23, No 6 (2025)

December

DOI: http://dx.doi.org/10.30811/jpl.v23i6

Table of Contents

Investigation of microstructural, mechanical, and electrical characteristics of CuNi5W alloy synthesized by warm compaction
Agung Ardiansyah, Bagus Prasetiyo, Suprianto Suprianto, Irfan Sitorus
PDF
723-728
Experimental evaluation of the thermal and exergy performance of a flat spiral-tube receiver for a parabolic dish collector
Ahmad Yonanda, Muhammad Raihan Junidy, Muhammad Irsyad, Amrizal Amrizal, Harmen Harmen, Dondi Kurniawan, Angga Darma Prabowo
PDF
729-738
Investigation for adhesion enhancement of hydroxyapatite coatings on Ti-12Cr alloy using the dipcoating method for orthopedic implant
Sanny Ardhy, Islahuddin Islahuddin, Meiki Eru Putra
PDF
739-742
Design of an automatic common water hyacinth flattening machine with an off-grid solar energy system
Adeguna Ridlo Pramurti, Mochammad Muqorrobin, Pangestuningtyas Diah Larasati, Syahid Syahid, Friska Ayu Fitrianti Sugiono
PDF
743-752
Influence of bonding compression and air gap on the acoustic absorption of spunbond–resinated felt composites
Hasan Basri, Dafit Feriyanto
PDF
753-758
Technical feasibility study of floating solar power for water hyacinth removal in Limboto Lake, Gorontalo
Rifaldo Pido, Rahmat Libunelo, Rahmad Hidayat Boli
PDF
759-764
Enhancing production effectiveness of the K-58 crankcase machining line through integrated TPM–FMEA approach
Zulkani Sinaga, Jhonni Sinaga
PDF
765-770
Development of phenolic-modified activated carbon for reduced energy band gap and improved semiconductor performance
Rahmadanti Rahmadanti, Agung Sugeng Widodo, Sulistyono Sulistyono, Purnami Purnami
PDF
771-778
Numerical and experimental investigation of scaling laws in PLA octet-truss lattice structures under compression load
Muhammad Yusri Dzal Yahya, Agus Sigit Pramono
PDF
779-789
Numerical investigation of heat reduction system in 42110 Lithium-Ion battery packs using cooling plate spacing variations
Bima Rakha Adhitama, James Julian, Fitri Wahyuni, Fathin Muhammad Madhudhu, Elvi Armadani
PDF
790-795
Effects of feed particle size distribution and chemical properties on roller press performance and comminution efficiency at plants 7 and 8 of PT Indocement Tunggal Prakarsa, Tbk
Mubarokah Nuriaini Dewi, Dwi Qurningsih, Samuel Armawan Sandi, Dody Guntama, Lukman Nulhakim, Lubena Lubena, Irma Agustin
PDF
796-801
Study of characterization of natural biomaterials Nypa fruticans extract for scaffold fabrication using 3D bio-printing method
Darwin Hendri, Irwansyah Irwansyah, Arhami Arhami, M. Rizki Maulana, Aulia Indriani
PDF
802-810
The effect of flap thickness on the hydrodynamic performance of an oscillating wave surge converter
James Julian, Rasya Aulia Nathania Nisa, Fitri Wahyuni, Riki Hendra Purba, Fathin Muhammad Madhudhu, Elvi Armadani
PDF
811-819
Performance analysis of a solar-powered maize sheller: production capacity and shelling efficiency
Hendradinata Hendradinata, Firdaus Firdaus, Toni Okviyanto, Tri Satya Ramadhoni, Muhammad Rizky Tolusha Putra, Muhammad Hafidzni Muttaqin, Taufikurrahman Taufikurrahman
PDF
820-828
The effect of biomass ratio and CaO/Si catalyst on hydrogen production from corncob–wood pellet gasification
Purbo Suwandono, Widya Wijayanti, Nova Risdiyanto Ismail, Dzulfikar Johan Akbar, Wisnu Setyo Catur Pambudi
PDF
829-836
Effect of water pressure and temperature on the perform-ance of a desalination reactor
Dany Alvian Dwibowo, Dan Mugisidi, Oktarina Heriyani, Rizky Alamsyach, Syahrul Amin
PDF
837-846
Taguchi-based optimization of CNC turning parameters to enhance surface finish of AISI 1045 steel
Kriswanto Kriswanto, Oktova Yusuf Briantoro, Rizqi Fitri Naryanto, Kaleb Priyanto, Jamari Jamari, Andri Setiyawan
PDF
847-853
Comparative time analysis of digital photogrammetry software using AI methods for design recovery in digital manufacturing
P. Paryanto, M. Faizin, R. Rusnaldy
PDF
854-862
The effect of copper thickness in catalytic converters on HC and CO emissions
Albaihaqi Hilmi, Yuniarto Agus Winoko
PDF
863-867
Experimental optimization of welding current, strip thickness, and spot number for the mechanical integrity of 18650 lithium-ion battery pack joints
Arman Arman, Widya Jufri, Baso Nasrullah
PDF
868-880
A hybrid pareto–fishbone and IoT-based monitoring framework for reducing DTY yarn defects
Deni Kurnia, Hanif Fakhrurroja, Marno Marno, Joniko Joniko
PDF
881-888
Investigation of the effects of fused deposition modeling process parameters on the dimensional accuracy of PLA+ using the Taguchi method
Pristiansyah Pristiansyah, Muhammad Yunus, Andi Meri, Soni Afriansyah
PDF
889-896
Microstructure and deformation behavior of Cu–Zn–Al–(Si) shape memory alloys under quenching controlled from the α/β phase region
Atik Setyani, Hendy Roesma Wardhana, Nur Amin, Ignatius Andre Setiawan, Nina Fapari Arif
PDF
897-903
Effect of nitrogen gas-assisted cooling on TIG weld distortion and mechanical properties of AA5083 aluminum alloy
Fuad Dwi Hanggara, Rama Dani Eka Putra, Tessa Zulenia Fitri, Handi Wilujeng Nugroho, Dhanang Suryo Prayogo
PDF
904-911