Taguchi-based optimization of CNC turning parameters to enhance surface finish of AISI 1045 steel

Kriswanto Kriswanto, Oktova Yusuf Briantoro, Rizqi Fitri Naryanto, Kaleb Priyanto, Jamari Jamari, Andri Setiyawan

Sari


Surface roughness is a critical indicator of machining quality, directly affecting the functional performance and service life of manufactured components. This study aims to optimize the surface roughness of AISI 1045 steel by varying parameters (cutting speed, feed rate, and depth of cut) using Taguchi L9 orthogonal array. Experiments were conducted on a FANUC 0i-Mate CNC lathe using Al-TiN-coated VNMG inserts. Moreover, the surface roughness was measured in accordance with ISO standards. Analysis of Variance (ANOVA) revealed the depth of cut was the most influential factor (45.21%), followed by cutting speed and feed rate. The Signal-to-Noise (S/N) ratio was identified as optimal surface roughness of 0.323 µm (N5 grade) at the parameter, with a cutting speed of 240 mm/min, a feed rate of 0.2 mm/rev, and a depth of cut of 0.6 mm. The novelty of this study is the demonstration that Taguchi's design and ANOVA combined can achieve reliable optimization results with considerably reduced experimental effort and offer practical industrial deployment, including for Small and Medium-sized Enterprises (SMEs). 


Kata Kunci


AISI 1045; Cutting Speed; Depth of Cut; Feed Rate; Optimization

Teks Lengkap:

PDF (English)

Referensi


S. Zeng and D. Pi, “Milling surface roughness prediction based on physics-informed machine learning,†Sensors, vol. 23, no. 10, 2023, doi: 10.3390/s23104969.

J. H. Lee, Y. S. Seo, and J. S. Kwak, “Surface roughness prediction and optimization in the REMF process using an integrated DBN-GA approach,†Int. J. Adv. Manuf. Technol., vol. 121, no. 9–10, pp. 5931–5942, 2022, doi: 10.1007/s00170-022-09652-9.

L. Zou, H. Fang, Y. Li, and S. Wu, “Roughness estimation of high-precision surfaces from line blur functions of reflective images,†Meas. J. Int. Meas. Confed., vol. 182, p. 109677, May 2021, doi: 10.1016/j.measurement.2021.109677.

H. Yang, H. Zheng, and T. Zhang, “A review of artificial intelligent methods for machined surface roughness prediction,†Tribol. Int., vol. 199, p. 109935, Jul. 2024, doi: 10.1016/j.triboint.2024.109935.

L. H. Kashkool, “Optimization of machining parameters of AISI 1045 steel for better surface finish and tool life using TiN coated carbide insert,†Tikrit J. Eng. Sci., vol. 29, no. 2, pp. 1–6, 2022, doi: 10.25130/tjes.29.2.1.

A. Polytechnic, “Optimization of process parameters of surface roughness and material removal rate in orthogonal turning of AISI 1045 carbon steel using Taguchi technique,†Ind. Eng. Lett., vol. 10, no. 4, pp. 16–25, 2021, doi: 10.7176/iel/11-1-03.

A. D. Abebe et al., “Comparative study on dry and wet machining during double tool turning of AISI 1045 steel,†Int. J. Innov. Sci. Eng. Technol., vol. 8, no. 9, pp. 71–101, 2021.

S. Y. Lubis, S. Djamil, and Y. K. Zebua, “Effect of cutting speed in the turning process of AISI 1045 steel on cutting force and built-up edge (BUE) characteristics of carbide cutting tool,†Sinergi, vol. 24, no. 3, p. 171, 2020, doi: 10.22441/sinergi.2020.3.001.

N. Siripath, N. Jantepa, S. Sucharitpwatskul, and S. Suranuntchai, “Integrating Taguchi method and finite element modelling for precision ball joint manufacturing with AISI 1045 medium carbon steel,†Int. J. Technol., vol. 15, no. 6, pp. 1801–1822, 2024, doi: 10.14716/ijtech.v15i6.7132.

Y. Zhao, B. Gong, Y. Liu, W. Zhang, and C. Deng, “Fatigue behaviors of ultrasonic surface rolling processed AISI 1045: The role of residual stress and gradient microstructure,†Int. J. Fatigue, vol. 178, p. 107993, Aug. 2023, doi: 10.1016/j.ijfatigue.2023.107993.

U. L. Adizue, A. D. Tura, E. O. Isaya, B. Z. Farkas, and M. Takács, “Surface quality prediction by machine learning methods and process parameter optimization in ultra-precision machining of AISI D2 using CBN tool,†Int. J. Adv. Manuf. Technol., vol. 129, no. 3–4, pp. 1375–1394, 2023, doi: 10.1007/s00170-023-12366-1.

N. Tamin et al., “Effect of feed rate on surface integrity and tool wear during short turning of AISI 1045 carbon steel,†Int. J. Mech. Prod. Eng. Res. Dev., vol. 10, no. 3, pp. 15305–15314, 2020, doi: 10.24247/ijmperdjun20201459.

H. M. Mohammad, N. H. J. Al Hasan, and M. A. Jabbar, “Optimization of sustainable carbon steel turning parameters,†Instrum. Mes. Metrol., vol. 23, no. 3, pp. 225–231, 2024, doi: 10.18280/i2m.230306.

K. Kaniapan, M. A. Ali, M. A. Sulaiman, M. Minhat, and M. S. Abdul Aziz, “Review on turning process parameters, responses and experimental method of AISI 1045 carbon steel,†in Proc. 8th Int. Conf. Mech. Eng. (ICOME 2021), Springer, 2022, pp. 467–476, doi:

1007/978-981-16-8954-3_44.

R. Rifelino, B. Rahim, and E. Indrawan, “Optimization of CNC turning parameters using Taguchi method,†Teknomekanik, vol. 4, no. 1, pp. 42–48, 2021, doi: 10.24036/TEKNOMEKANIK.V4I1.11072.

A. T. Abbas et al., “Effects of tool edge geometry and cutting conditions on the performance indicators in dry turning AISI 1045 steel,†Machines, vol. 11, no. 3, 2023, doi: 10.3390/machines11030397

Mitsubishi Materials Corporation, “Turning inserts | Series list,†2024. [Online]. Available: https://www.mitsubishicarbide.net/mhg/enuk/turning_inserts/no_srs/20092681

A. T. Abbas et al., “Multi-objective optimization of performance indicators in turning of AISI 1045 under dry cutting conditions,†Metals, vol. 13, no. 1, pp. 1–22, 2023, doi: 10.3390/met13010096.

MatWeb LLC, “AISI 1045 medium carbon steel,†2024. [Online]. Available: https://www.matweb.com/search/DataSheet.aspx?MatGUID=4b0553daf9c245e684f2199a48179d89&ckck=1

M. Kasim, H. Siregar, and R. Ilhami, "Pengaruh parameter proses terhadap kekasaran permukaan pada proses milling CNC dengan menggunakan metode Taguchi," *Jurnal Polimesin*, vol. 21, no. 4, pp. 82–89, 2023, doi: 10.30811/jpl.v21i4.4039.

Kriswanto, W. Sumbodo, W. Aryadi, and J. Jamari, "Optimization of milling parameters to increase surface quality and machining time of the Bohler M303 Extra," IOP Conf. Ser.: Earth Environ. Sci., vol. 700, no. 1, Art. no. 012009, Mar. 2021, doi: 10.1088/1755-1315/700/1/012009.

W. Sumbodo, K. Kriswanto, and J. Jamari, "Simulation and optimization of machining time during milling AISI P20 steel," *IOP Conf. Ser.: Earth Environ. Sci.*, vol. 700, no. 1, Art. no. 012002, Mar. 2021, doi: 10.1088/1755-1315/700/1/012002.




DOI: http://dx.doi.org/10.30811/jpl.v23i6.7107

Refbacks

  • Saat ini tidak ada refbacks.


Bookmark and Share


##submission.license.cc.by-sa4.footer##