Fluid pressure optimization of a PID-controlled hydraulic jack for enhanced lifting efficiency and stability

Hairil Budiarto, Ibnu Irawan, Achmad Imam Sudianto, Ahmad Sahru Romadhon

Sari


Hydraulic and mechanical jacks are widely used for lifting applications but face limitations in efficiency and load handling. Despite being powerful, hydraulic jacks are prone to pressure loss and fluid leakage under static load, while mechanical systems lack automation and practicality. This research presents a hybrid hydraulic jack system integrating a DC motor-driven screw actuator and proportional–integral–derivative (PID) control for adaptive fluid pressure regulation. The purpose of this research is to develop an automatic hydraulic jack that integrates mechanical and hydraulic systems to improve the efficiency of load lifting time and reduce the risk of fluid leakage due to prolonged static pressure. The system was tested under three different loads: 90 kg, 110 kg, and 130 kg, with corresponding pressure setpoints of 170, 195, and 223 psi. Using the Ziegler–Nichols tuning method, the PID controller achieved high accuracy with error deviations of 1.1 psi, 0.1 psi, and 1.5 psi, respectively. These results represent a 95–99% precision rate in pressure regulation, compared to uncontrolled systems. The findings demonstrate the ability of the system to maintain pressure stability under varying load conditions, therefore reducing the risk of leakage and mechanical fatigue. This PID-based jack offers a cost-effective and efficient alternative to conventional power-pack hydraulic systems, particularly in mobile or resource-constrained applications.


Kata Kunci


PID control, hydraulic jack, push rod screw, fluid pressure

Teks Lengkap:

PDF (English)

Referensi


S. Patidar, “Mechanism of Inbuilt Automatic Hydraulic Jack used for Light and Heavy Vehicles,†International Journal for Research in Applied Science and Engineering Technology, vol. 9, no. 12, pp. 1919–1925, Dec. 2021, doi: https://doi.org/10.22214/ijraset.2021.39654.

“Design and Fabrication of Automated Inbuilt Hydraulic Jack for Light Motor Vehicle,†International Journal of Engineering and Advanced Technology, vol. 8, no. 6S, pp. 545–549, Sep. 2019, doi: https://doi.org/10.35940/ijeat.f1110.0886s19.

A. ur Rehman, Marwan Abdebary, Amer Alzayat, and J. Quintero, “First Installation of Hydraulic Jet Pump for High Viscous Oil in Shaikan Oil Field with Significant Concentration of Hydrogen Sulfide,†vol. 13, Sep. 2024, doi: https://doi.org/10.2118/220622-m s.

S. B. Kumar, Md Saim Hossem, and A. Sayed, “A Comprehensive Review of Hydraulic Systems in Aerospace and Construction Engineering,†Control Systems and Optimization Letters, vol. 2, no. 3, pp. 266–273, Nov. 2024, doi: https://doi.org/10.59247/csol.v2i3.127.

Lawal, S. Sius, Duniya, C. Bitiyong, M. Babatunde, and Oluwaseyi, “Development and Exploration of Controlled Automated Scissors Car Jack for Vehicle Maintenance,†Zamfara International Journal of Education, vol. 3, no. 2, pp. 2814–1369, 2023, doi: https://doi.org/10.5281/zenodo.8382966.

Arinola Bola Ajayi and Musiliu Olalekan Adeyinka, “Development of an Automatic Scissors Screw Car Jack,†ABUAD Journal of Engineering Research and Development (AJERD), vol. 7, no. 2, pp. 193–206, Aug. 2024, doi: https://doi.org/10.53982/ajerd.2024.0702.19-j.

T. Vrålstad, A. Saasen, E. Fjær, T. Øia, J. D. Ytrehus, and M. Khalifeh, “Plug & abandonment of offshore wells: Ensuring long-term well integrity and cost-efficiency,†Journal of Petroleum Science and Engineering, vol. 173, pp. 478–491, Feb. 2019, doi: https://doi.org/10.1016/j.petrol.2018.10.049.

Z. Asif, Z. Chen, C. An, and J. Dong, “Environmental Impacts and Challenges Associated with Oil Spills on Shorelines,†Journal of Marine Science and Engineering, vol. 10, no. 6, p. 762, May 2022, doi: https://doi.org/10.3390/jmse10060762.

M. Atif, F. Mumtaz, and M. Adeel, “Design and fabrication of a motorized screw jack,†6th Smart Cities Symposium (SCS 2022), pp. 114–119, 2022, doi: https://doi.org/10.1049/icp.2023.0358.

L. Wang, “Application of Intelligent Sensors in the Collection of Electrical Engineering Automation Equipment,†Informatica, vol. 49, no. 9, Feb. 2025, doi: https://doi.org/10.31449/inf.v49i9.5499.

M. H. Setiawan, A. Ma’arif, Much. F. Saifuddin, and W. A. Salah, “A Comparative Study of PID, FOPID, ISF, SMC, and FLC Controllers for DC Motor Speed Control with Particle Swarm Optimization,†International Journal of Robotics and Control Systems, vol. 5, no. 1, pp. 640–660, Feb. 2025, doi: https://doi.org/10.31763/ijrcs.v5i1.1764.

T. T. Yetayew, T. G. G/Meskel, and D. M. G/michael, “A Concise Evaluation of Auto-tuned PID and Fuzzy Logic Controllers for Speed Control of a DC-Motor,†Springer eBooks, pp. 256–268, Jan. 2022, doi: https://doi.org/10.1007/978-3-030-93709-6_17.

A. N. Aborobaa, K. A. Ghamry, A. Saleh, and M. H. Mabrouk, “Mathematical model and PID control of a hydraulic motor using on/off solenoid valve,†Journal of Physics Conference Series, vol. 2299, no. 1, p. 012003, Jul. 2022, doi: https://doi.org/10.1088/1742-6596/2299/1/012003.

Mohamad Syahrul Mubarok, S. J. Zarrouk, J. Cater, Akhmad Mundakir, Eko Agung Bramantyo, and Yoong Ping Lim, “Real-time enthalpy measurement of two-phase geothermal fluid flow using load cell sensors: Field testing results,†vol. 89, pp. 101930–101930, Jan. 2021, doi: https://doi.org/10.1016/j.geothermics.2020.101930.

H. Kogler, “Digital Hydraulic Transformer Concepts for Energy-Efficient Motion Control,†Actuators, vol. 14, no. 2, pp. 54–54, Jan. 2025, doi: https://doi.org/10.3390/act14020054.

Felipe et al., “Gain-analytical equations generalized for FOPID controllers - An application with DC-DC power converters,†e-Prime - Advances in Electrical Engineering Electronics and Energy, pp. 100967–100967, Mar. 2025, doi: https://doi.org/10.1016/j.prime.2025.100967.

D. Pratama, “Perancangan Kemudi Kendaraan Listrik Penghindar Halangan Menggunakan Kontrol Logika Fuzzy,†Jurnal Teknik Elektro ITP, vol. 9, no. 1, pp. 30–36, Jan. 2020, doi: https://doi.org/10.21063/jte.2020.3133906.

A. T. Negara, I. Ardiyanto, and O. Wahyunggoro, “Tuning of Fractional-Order PID Controller for Electro-Hydraulic Servo Valve System,†2019 International Conference on Information and Communications Technology (ICOIACT), Jul. 2019, doi: https://doi.org/10.1109/icoiact46704.2019.8938409

Mohga Abd Alrhman, Muawia Mohamed Ahmed, "Design of a Tuned PID Controller for a Hydraulic System", International Journal of Science and Research (IJSR), Volume 5 Issue 8, August 2016, pp. 1218-1220, DOI: https://www.doi.org/10.21275/11081604

J. Li, H. Yang, and H. Ji, “Characterization of Two-Cylinder Parallel Electro-hydraulic Force/Position Synchronization Based on RBF Fuzzy Neural Network Control,†International Journal of Fuzzy Systems, Nov. 2024, doi: https://doi.org/10.1007/s40815-024-01846-5.

W. Mo, N. Liu, L. Li, and H. Han, “Application of PID control in hydraulic synchronous system of cleaning equipment,†Journal of Physics Conference Series, vol. 1748, no. 6, pp. 062064–062064, Jan. 2021, doi: https://doi.org/10.1088/1742-6596/1748/6/062064.

J. He, S. Su, H. Wang, F. Chen, and B. Yin, “Online PID Tuning Strategy for Hydraulic Servo Control Systems via SAC-Based Deep Reinforcement Learning,†Machines, vol. 11, no. 6, pp. 593–593, May 2023, doi: https://doi.org/10.3390/machines11060593.

W. Ma, S. Ma, W. Qiao, D. Cao, and C. Yin, “Research on PID Controller of Excavator Electro-Hydraulic System Based on Improved Differential Evolution,†Machines, vol. 11, no. 2, pp. 143–143, Jan. 2023, doi: https://doi.org/10.3390/machines11020143.

W. Mo, N. Liu, L. Li, and H. Han, “Application of PID control in hydraulic synchronous system of cleaning equipment,†Journal of Physics Conference Series, vol. 1748, no. 6, pp. 062064–062064, Jan. 2021, doi: https://doi.org/10.1088/1742-6596/1748/6/062064.

Meilia Safitri, Atikah Surriani, and Sotya Anggoro, “Evaluation of adaptive PID for oxytocin pole massager temperature control,†AIP conference proceedings, vol. 3236, pp. 020023–020023, Jan. 2024, doi: https://doi.org/10.1063/5.0224072.

A. Ferrara and C. Vecchio, “Second order sliding mode control of vehicles with distributed collision avoidance capabilities,†Mechatronics, vol. 19, no. 4, pp. 471–477, Jun. 2009, doi: https://doi.org/10.1016/j.mechatronics.2008.11.002.

E. B. Priyanka, C. Maheswari, S. Thangavel, and M. P. Bala, “Integrating IoT with LQR-PID controller for online surveillance and control of flow and pressure in fluid transportation system,†Journal of Industrial Information Integration, vol. 17, p. 100127, Mar. 2020, doi: https://doi.org/10.1016/j.jii.2020.100127.

N. Pipattikanan and R. Chaichaowarat, “Friction Characterization of Threadless Linear Transmission System Using Rolling-Element Bearings to Create Imaginary Helical Pattern,†2024 IEEE International Conference on Robotics and Biomimetics (ROBIO), pp. 1329–1334, Dec. 2024, doi: https://doi.org/10.1109/robio64047.2024.10907276.

A. Wang, D. Wang, X. Wang, F. Zhang, Evarist Petro Mwaigaga, and X. Wang, “Design, Analysis, and Performance Comparison of a Permanent Magnet Synchronous Machine With Multiple Excitation-Drive Ports,†IEEE Transactions on Energy Conversion, pp. 1–13, Jan. 2025, doi: https://doi.org/10.1109/tec.2025.3550969.

A. D. M. Africa, J. O. Q. Chua and J. L. H. Solis, "PID Tuning of Speed Controller Using Ziegler-Nichols and Manual Method DC Motor," 2023 IEEE 15th International Conference on Humanoid, Nanotechnology, Information Technology, Communication and Control, Environment, and Management (HNICEM), Coron, Palawan, Philippines, 2023, pp. 1-6, https://doi.org/10.1109/HNICEM60674.2023.10589041




DOI: http://dx.doi.org/10.30811/jpl.v23i3.6650

Refbacks

  • Saat ini tidak ada refbacks.


Bookmark and Share


##submission.license.cc.by-sa4.footer##