Design and development of a microcontroller-based automatic wet scrubber system for welding smoke control using CO and gas indicator sensors

Jufri Jufri; Enni Sulfiana; Saktiani Karim; Muhammad Ridwan Anwar; Rival Alviansyah; Bintang Jayakusuma; Yuda Agung Wirawan

doi:10.30811/jpl.v24i1.8225

Design and development of a microcontroller-based automatic wet scrubber system for welding smoke control using CO and gas indicator sensors

Jufri Jufri, Enni Sulfiana, Saktiani Karim, Muhammad Ridwan Anwar, Rival Alviansyah, Bintang Jayakusuma, Yuda Agung Wirawan

Abstract

Welding workshops are one of the work environments with a high potential for air pollution due to welding smoke containing heavy metal particles and hazardous gases such as Carbon Monoxide (CO). This research aims to design and build a wet scrubber-based welding smoke cleaning device that works automatically using a gas sensor and a microcontroller system. This system consists of an exhaust fan, a diaphragm pump, a drum filter containing activated charcoal and stone, and MQ-2 and MQ-7 sensors that detect smoke. The system automatically activates when hazardous gases are detected. System calculations show an air flow rate of 258.84 m³/hour and a pump water flow rate of 0.00208 m³/minute. This device was designed with space efficiency, low power consumption (90 W), and ease of maintenance in mind. Each experimental condition was tested for 10 minutes and repeated three times. MQ-2 and MQ-7 sensor readings were recorded at 1- second intervals. The inlet (Cin) and outlet (Cout) values were obtained from the average stabilized sensor readings measured before and after the activation of the wet scrubber system. The experimental results showed that the proposed system achieved relative reductions of up to 19.41% for smoke indicator readings and 17.55% for CO readings at full water flow rate, while reductions of 13.69% (smoke) and 15.28% (CO) were observed at half water flow rate. These results are based on sensor-based relative measurements and indicate the practical performance of the prototype system. This research is expected to provide a practical solution for maintaining air quality in small to mediumscale welding workshops.

Keywords

wet scrubber; welding; air purifier; automatic sensor; exhaust fan; air pollutant

Full Text:

PDF

References

N. Fatkhurrahman, I. R. Juliasari, and N. Z., “Verification of a low-cost particulate sensor as a particulate sensor in modified wet scrubber technology,” Journal of Industrial Pollution Prevention Technology Research, pp. 5–8, 2016.

F. Bahari, “How wet scrubbers eliminate air pollution,” FLOOTANK Plastic Engineering & Environmental Technologies, 2022. [Online].

A. Budianto, K. Al, N. M. Apriza, and R. Wijaya, “Identification of fine particle emission concentration in a closed room with an automatic air conditioning system,” Journal of Education, Science, Geology, and Geophysics (GeoScienceEd Journal), vol. 5, no. 4, pp. 808–813, 2024, doi: 10.29303/goescienceed.v5i4.509.

B. A. Danzomo, “Performance evaluation of a wet scrubber system for industrial air pollution control,” Journal, vol. 7, no. 12, pp. 1669–1677, 2012.

Y. Dianti, “Design of a wet scrubber filter for temperature reduction and tar content reduction in syngas from the gasification process,” Angewandte Chemie International Edition, vol. 6, no. 11, pp. 951–952, 2021.

S. Dubey, H. Rohra, and A. Taneja, “Assessing the effectiveness of air purifiers (HEPA) for controlling indoor particulate pollution,” Heliyon, vol. 7, no. 9, Art. no. e07976, 2021, doi: 10.1016/j.heliyon.2021.e07976.

A. Farioli, F. S. Violante, C. La Vecchia, E. Negri, C. Pelucchi, G. Spatari, P. Boffetta, and E. Pira, “Temporal patterns of exposure to asbestos and risk of asbestosis,” Journal of Occupational and Environmental Medicine, vol. 60, no. 6, pp. 536–541, 2018, doi: 10.1097/JOM.0000000000001260.

N. A. Firdaus, B. M. Wulandari, and R. Novembrianto, “Analysis of bag filter and wet scrubber unit efficiency on particulate matter, SO₂, NO₂, and opacity parameters in the iron and steel industry in Surabaya,” Environmental Engineering Journal ITATS, vol. 3, no. 1, pp. 57–64, 2023, doi: 10.31284/j.envitats.2023.v3i1.3838.

Z. D. Ghasypham, “Design and construction of water level and discharge detection at the confluence of three rivers based on the Internet of Things,” Journal of Informatics and Applied Electrical Engineering, vol. 11, no. 3S1, 2023, doi: 10.23960/jitet.v11i3s1.3564.

Gunawan, B. Sugiantoro, Ngisomudin, Warso, and N. Supriyana, “Optimization of vortex wet scrubber with dolomite suspension for more efficient capture of ultrafine carbon particles and acidic pollutants,” ITEKS, vol. 16, no. 2, pp. 29–39, 2024.

A. A. Harvianti, “What is a scrubber? Its role in industrial and environmental sustainability,” 2025. [Online].

P. Khairumizam, “Experimental study of venturi scrubber implementation in a coal gasification system,” pp. 8–26, 2018.

D. Mussanti, “Air pollution control: Wet scrubbers,” 2020.

H. A. Nannuba, S. Prajogo, and A. S. Kurniasetiawati, “Design of a wet scrubber with a capacity of 0.72 m³/hour for the biogas purification process from cow manure,” in Proc. Industrial Research Workshop and National Seminar, vol. 13, no. 1, pp. 850–858, 2022, doi: 10.35313/irwns.v13i01.4178.

S. Y. Pratama, “Analysis of electrical power requirements for propulsion of religious tourism passenger boats in Sayung,” 2023.

A. Qolik, Y. Yoto, B. Basuki, S. Sunomo, and W. Wahono, “The dangers of welding smoke and radiation for welding workers in the informal sector,” Journal of Mechanical Engineering and Learning, vol. 1, no. 1, pp. 1–4, 2018, doi: 10.17977/um054v1i1p1-4.

F. Rahmawati, B. P. Samadikun, and M. Hadiwidodo, “Performance evaluation of cyclone particulate controller and wet scrubber unit in paper mill 7/8 PT. Pura Nusapersada Kudus,” Journal of Precipitation: Communication Media and Environmental Engineering Development, vol. 17, no. 2, pp. 144–153, 2020, doi: 10.14710/precipitasi.v17i2.144-153.

P. Setyadi and S. E. Nurcahyo, “Calculation of pressure drop in a clean water plumbing system using Microsoft Excel as a database in building ‘X’ in South Jakarta,” in Proc. National Seminar on Science and Technology, Faculty of Engineering, Universitas Muhammadiyah Jakarta, pp. 1–12, 2017.

I. Tika, ATI Makassar Polytechnic, 2020.

K. H. Kim, E. Kabir, and S. Kabir, “A review on the human health impact of airborne particulate matter,” Environment International, vol. 74, pp. 136–143, 2019.

X. Li, Y. Wang, and J. Chen, “Performance evaluation of wet scrubbers for fine particulate matter removal in industrial applications,” Journal of Hazardous Materials, vol. 384, Art. no. 121130, 2020.

H. Wang, Y. Zhang, and J. Liu, “Removal of welding fumes using compact wet scrubber systems: Experimental and numerical analysis,” Journal of Cleaner Production, vol. 278, Art. no. 123135, 2021.

Y. Zhou, Z. Li, and Q. Sun, “Gas–liquid interaction mechanisms in wet scrubbers for air pollution control,” Chemical Engineering Journal, vol. 431, Art. no. 134145, 2022.

R. Chen, B. Zhao, and C. Chen, “Control of ultrafine particles in welding workshops using local exhaust and wet scrubbing systems,” Building and Environment, vol. 231, Art. no. 109120, 2023.

Vaaraslahti, K., Laitinen, A., & Keskinen, J. (2002a). Spray charging of droplets in a wet scrubber. Journal of the Air & Waste Management Association, 52(2), 175–180. https://doi.org/10.1080/10473289.2002.10470776.

Wang, Z., Chen, Z., Shahid, I., Asif, Z., & Haghighat, F. (2025). Indoor air quality assessment through IoT sensor technology: A Montreal–Qatar case study. Atmosphere, 16(5), 574. https://doi.org/10.3390/atmos16050574.

Prakoso, M. a. A., & Rakhmawati, L. (2021). Real time factory smokes monitoring system using Android smartphone. INAJEEE Indonesian Journal of Electrical and Eletronics Engineering, 4(1), 16–21. https://doi.org/10.26740/inajeee.v4n1.p16-21.

Kinanti, A. H., & Purlinda, D. E. (2025). FAKTOR RISIKO PAPARAN CO TERHADAP KADAR COHB PADA PEKERJA BENGKEL KENDARAAN BERMOTOR KOTA SEMARANG. Jurnal Medika, 9(2), 56–64. https://doi.org/10.53861/jmed.v9i2.466.

Pietro, G., & Elisabetta, B. (2025). Analysis of mass transfer efficiency in a compact wet scrubber. CINECA IRIS Institutial Research Information System (University of Pisa). https://doi.org/10.3303/cet25117105.

DOI: http://dx.doi.org/10.30811/jpl.v24i1.8225