Performance evaluation of a laboratory-scale Pelton turbine under variable nozzle distance and valve opening

Aini Lostari; Didik Sugiono; Miftahul Ulum; Umi Kulsum; Yudi Hartono

doi:10.30811/jpl.v24i3.8200

Performance evaluation of a laboratory-scale Pelton turbine under variable nozzle distance and valve opening

Aini Lostari, Didik Sugiono, Miftahul Ulum, Umi Kulsum, Yudi Hartono

Abstract

Pelton turbines are impulse turbines widely used in micro-hydro power systems operating under high-head and low-flow conditions. Their performance depends strongly on the quality of the water jet impacting the runner buckets, which is influenced by nozzle distance and valve opening. This study experimentally investigated the effects of nozzle distance (60, 70, and 80 mm) and valve opening (30°, 60°, and 90°) on the hydraulic power, turbine power, electrical power, and efficiency of a laboratory-scale Pelton turbine. Turbine rotational speed was measured using a tachometer, while voltage and current were measured using a multimeter to determine power output. The results showed that increasing the valve opening increased hydraulic, turbine, and electrical power due to higher flow rate and jet kinetic energy. However, the turbine efficiency showed non-linear behavior because it was influenced by the quality of the jet and the effectiveness of momentum transfer. The maximum turbine power of 10.52 Watts and electrical power of 10.58 Watts were obtained at a nozzle spacing of 80 mm and a valve opening of 90°. Meanwhile, optimum efficiency was achieved at a nozzle distance of 80 mm and a valve opening of 30%, indicating that optimum conditions do not always occur at maximum flow. The results of this study indicate that the combination of nozzle distance and valve opening significantly influences Pelton turbine performance and is important for optimizing laboratory-scale micro-hydro systems.

Keywords

Pelton turbine; nozzle distance; valve opening; turbine power; efficiency

Full Text:

PDF

References

Paish, O., “Small hydro power: technology and current status,” Renewable and Sustainable Energy Reviews, vol. 6, no. 6, pp. 537–556, 2002.

Kaunda, C. S., Kimambo, C. Z., and Nielsen, T. K., “Hydropower in the context of sustainable energy supply: A review of technologies and challenges,” Renewable and Sustainable Energy Reviews, vol. 16, no. 7, pp. 5250–5264, 2012.

Widodo, A., Nugroho, G., and Santoso, B., “Development of laboratory-scale Pelton turbine for micro hydro application,” Journal of Mechanical Engineering, vol. 10, no. 2, pp. 85–92, 2020.

Putra, R. P., Pranowo, and Hadi, S., “Performance analysis of micro hydro power plant using Pelton turbine,” International Journal of Renewable Energy Research, vol. 11, no. 3, pp. 1105–1112, 2021.

Brekke, H., Pelton Turbines: Design, Operation and Maintenance, Trondheim: Norwegian University of Science and Technology, 2010.

Deng, Q., Zhang, Y., and Liu, H., “Numerical investigation of nozzle jet alignment effect on Pelton turbine performance,” Renewable Energy, vol. 203, pp. 1125–1135, 2023.

Mockmore, C. A., and Merryfield, F., The Banki Water Turbine, Oregon State College Engineering Experiment Station, 1949.

Streeter, V. L., Wylie, E. B., and Bedford, K. W., Fluid Mechanics, 9th ed., Boston: McGraw-Hill, 1998.

S. Mahardika, D. Sugiono, R. Irwansyah, and H. Novianto, “Analysis of the effect of additional number of 24, 26 and 28 blade of Pelton turbine from PLA to turbine performance,” Journal of Mechanical Engineering Manufactures Materials and Energy, vol. 8, no. 1, pp. 1–10, 2024.

S. Mahardika, D. Sugiono, Supardi, and M. H. Farid, “Studi eksperimental pengaruh variasi kecepatan putar pompa terhadap performa turbin Pelton,” Majamecha, vol. 5, no. 2, pp. 99–105, 2023.

Arun Kumar, A., Saini, R. P., and Kumar, S., “Experimental study of Pelton turbine performance,” Energy Procedia, vol. 90, pp. 426–433, 2016.

Jadhav, H. T., and Vanjar, H. S., “Effect of nozzle parameters on Pelton turbine performance,” International Journal of Engineering Research, vol. 5, no. 6, pp. 150–155, 2017.

Singh, P., and Nestmann, F., “Experimental investigation of impulse turbine,” Renewable Energy, vol. 118, pp. 930–939, 2018.

Deng, Q., et al., “Experimental study on Pelton turbine efficiency,” Energy Conversion and Management, vol. 256, pp. 115–124, 2023.

Adhiela, R., Prakoso, A., and Nugroho, S., “Effect of nozzle diameter on Pelton turbine performance,” Journal of Mechanical Engineering Research, vol. 14, no. 2, pp. 45–52, 2024.

Iswidiyanto, Fahruddin, and Iswanto, “Experimental study of valve opening effect on Pelton turbine,” Politeknik Journal of Mechanical Engineering, vol. 18, no. 1, pp. 12–18, 2024.

Hartono, Y., and Amin, M., “Laboratory scale Pelton turbine performance analysis,” International Journal of Mechanical Engineering, vol. 20, no. 1, pp. 33–41, 2025.

Setiawan, D., Nugraha, R., and Santoso, H., “Effect of nozzle angle on Pelton turbine performance,” Journal of Renewable Energy Engineering, vol. 9, no. 1, pp. 21–30, 2025.

Khurmi, R. S., and J. K. Gupta. A Textbook of Thermal Engineering. New Delhi: S. Chand & Company Ltd., 2005.

R. D. Kusumanto and M. N. Nugraha,“Archimedes screw turbine application on portable mini hydropower plant,”Jurnal Polimesin, vol. 21, no. 1, pp. 1–6, 2023.

DOI: http://dx.doi.org/10.30811/jpl.v24i3.8200