Rotary friction welding of 304 stainless steel: parametric study, mechanical properties, and microstructure of the joint
Abstract
In the rotary friction welding process, the selection of process parameters affects the friction, heat generation, and joint formation. These factors collectively cause microstructural changes that determine the mechanical properties of the joint. Therefore, the process parameters, microstructure, and mechanical properties were interconnected during rotary friction welding. This study examined the influence of process parameters on their correlation with microstructure and mechanical properties in the rotary friction welding of 304 SS. A 3×4 full factorial experimental design was used to evaluate the effects of the process parameters on the microstructure and strength of 304 SS joints produced through rotary friction welding. An accurate evaluation of joint strength was performed using the notch tensile test technique. The joint with the highest strength was achieved by applying a combination of friction pressure and friction time at 55 bars and 3 seconds, respectively, resulting in a welding efficiency of 103.6%. A very low friction time (i.e., 5 s) produced a weak joint, which should be avoided. The welding process created three distinct structural zones in the joint: a joint structure finer than the parent metal structure, a partially deformed structure, and a heat-affected zone with deformation. Hardness tests of the joints showed a high hardness in the deformed structure. The formed structure contributes to the resulting joint strength.
Keywords
Full Text:
PDFReferences
A. Prastyo, F. Ibrahim, and M. Badaruddin, “Analysis of Mechanical Properties of CD 304 SS at High Temperature Transient Condition,” J. Polimesin, vol. 20, no. 2, pp. 169–175, 2022, [Online]. Available: https://e-jurnal.pnl.ac.id/polimesin/article/view/2995
K. T. Sunny and N. N. Korra, “A systematic review about welding of super austenitic stainless steel,” in Materials Today: Proceedings, Elsevier Ltd, 2021, pp. 4378–4381. doi: 10.1016/j.matpr.2021.05.185.
A. R. Hakim and I. Imran, “Analisa pengaruh variasi kampuh terhadap hasil pengelasan SMAW pada stainless steel 304 menggunakan pengujian ultrasonic dan kekuatan tarik,” J. Polimesin, vol. 18, no. 1, pp. 30–38, 2020.
V. A. Alza, “Mechanical Properties and Microstructure, in welded joints of Low and Medium Carbon Steels, Applying Rotary Friction,” Int. J. Recent Technol. Eng. ISSN, pp. 2277–3878, 2020.
Y. Yohanes, R. Abdurrahman, and A. Ridwan, “Finite element study on rotary friction welding process for mild steel,” in IOP Conference Series: Materials Science and Engineering, IOP Publishing, 2019, p. 012111. doi: 10.1088/1757-899X/620/1/012111.
S. T. Selvamani, K. Palanikumar, K. Umanath, and D. Jayaperumal, “Analysis of friction welding parameters on the mechanical metallurgical and chemical properties of AISI 1035 steel joints,” Mater. Des., vol. 65, pp. 652–661, 2015.
Y. Lu, D. Li, J. Zhang, C. Bi, F. Sun, and Y. Yang, “Effects of Friction Pressure on Microstructures and Mechanical properties of friction welded Super304H austenitic welding joints,” in IOP Conference Series: Materials Science and Engineering, IOP Publishing, 2020, p. 012002.
G. Wang, J. Li, W. Wang, J. Xiong, and F. Zhang, “Study on the effect of energy-input on the joint mechanical properties of rotary friction-welding,” Metals (Basel)., vol. 8, no. 11, p. 908, 2018.
H. Mesmari and F. Krayem, “Mechanical and microstructure properties of 304 stainless steel friction welded Joint,” Int. Res. J. Eng. Sci. Technol. Innov., vol. 2, no. 4, pp. 65–74, 2013.
N. Mathiazhagan, T. Senthilkumar, and V. Balasubramanian, “Effect of Mechanical Properties and Microstructural Characteristics of Friction Welded Austenitic Stainless Steel Joints,” Aust. J. Basic Appl. Sci., vol. 9, no. 27, pp. 267–276, Aug. 2015, [Online]. Available: www.ajbasweb.com
M. Sahin, “Evaluation of the joint-interface properties of austenitic-stainless steels (AISI 304) joined by friction welding,” Mater. Des., vol. 28, no. 7, pp. 2244–2250, 2007.
M. Acarer and B. Demir, “An investigation of mechanical and metallurgical properties of explosive welded aluminum-dual phase steel,” Mater. Lett., vol. 62, no. 25, pp. 4158–4160, May 2008, doi: 10.1016/j.matlet.2008.05.060.
M. Mohanta, S. Kar, D. Mohanta, and A. M. Mohanty, “Experimental Analysis and Parametric Optimization of 6065-Aluminium Alloy in Rotary Friction Welding,” Int. J. Adv. Mech. Eng., vol. 8, no. 1, pp. 111–118, 2018, [Online]. Available: http://www.ripublication.com
F. Khalfallah, Z. Boumerzoug, S. Rajakumar, and E. Raouache, “Optimization by RSM on rotary friction welding of AA1100 aluminum alloy and mild steel,” Int. Rev. Appl. Sci. Eng., 2020.
Y. Chapke, D. Kamble, and S. M. S. Shaikh, “Friction welding of Aluminium Alloy 6063 with copper,” in E3S web of conferences, EDP Sciences, 2020, p. 02004.
A. Handa and V. Chawla, “Investigation of mechanical properties of friction-welded AISI 304 with AISI 1021 dissimilar steels,” Int. J. Adv. Manuf. Technol., vol. 75, pp. 1493–1500, 2014.
Y. Belkahla et al., “Rotary friction welded C45 to 16NiCr6 steel rods: statistical optimization coupled to mechanical and microstructure approaches,” Int. J. Adv. Manuf. Technol., vol. 116, pp. 2285–2298, 2021.
Z. Yanushkevich, A. Lugovskaya, A. Belyakov, and R. Kaibyshev, “No Title,” Mater. Sci. Eng. A, vol. 667, pp. 279–285, 2016, [Online]. Available: https://www.sciencedirect.com/science/article/abs/pii/S0921509316305019
G. E. P. Box, J. S. Hunter, and W. G. Hunter, “Statistics for experimenters,” in Wiley series in probability and statistics, Wiley Hoboken, NJ, 2005.
H. Firmanto, S. Candra, M. A. Hadiyat, and Y. Haryono, “Influence of Heating Stage Parameters on the Joint Strength of Rotary Friction Welded AISI 1045 and AISI 304 Steels: A Polynomial Model,” in Materials Science Forum, Trans Tech Publ, 2022, pp. 157–163.
A. Vairis and M. Petousis, “Designing experiments to study welding processes: using the Taguchi method,” J. Eng. Sci. Technol. Rev., vol. 2, no. 1, pp. 99–103, 2009.
V. Olden, Z. L. Zhang, E. Østby, B. Nyhus, and C. Thaulow, “Notch tensile testing of high strength steel weldments,” in 2nd international symposium on high strength steel, 2002.
E. P. Alves, R. C. Toledo, F. Piorino Neto, F. G. Botter, and C. Ying An, “Experimental thermal analysis in rotary friction welding of dissimilar materials,” J. Aerosp. Technol. Manag., vol. 11, p. e4019, 2019.
M. Gavalec, I. Barényi, and H. Chochlíková, “Properties and microstructure of joints created by the method of rotary friction welding,” in Proceedings 31st International Conference on Metallurgy and Materials, Brno, 2022, pp. 376–381. doi: https://doi.org/10.37904/metal.2022.4406.
M. Gavalec, I. Barenyi, M. Krbata, M. Kohutiar, S. Balos, and M. Pecanac, “The effect of rotary friction welding conditions on the microstructure and mechanical properties of Ti6Al4V titanium alloy welds,” Materials (Basel)., vol. 16, no. 19, 2023, doi: https://doi.org/10.3390/ma16196492.
M. C. Zulu and P. M. Mashinini, “Analysis of defect formation during rotary friction welding of titanium alloy,” in Proceedings of 2021 IEEE 12th International Conference on Mechanical and Intelligent Manufacturing Technologies, ICMIMT 2021, 2021, pp. 7–11. doi: 10.1109/ICMIMT52186.2021.9476169.
A. Sasmito, A. S. Hermawan, and Sunyoto, “Rotary friction welding properties of AA5083-H112/AA7075-T6 joints: Parameter and low temperature effect,” Mater. Sci. Technol., 2024, doi: https://doi.org/10.1177/02670836241234198.
A. B. Dawood, S. I. Butt, G. Hussain, M. A. Siddiqui, A. Maqsood, and F. Zhang, “Thermal model of rotary friction welding for similar and dissimilar metals,” Metals (Basel)., vol. 7, no. 6, p. 224, 2017.
G. L. Wang, J. L. Li, J. T. Xiong, P. Y. Ma, W. L. Wang, and F. S. Zhang, “A heat flux model for rotary friction welding of 304 stainless steel,” Mater. Res. Express, vol. 6, no. 2, p. 026558, 2018.
P. Gaikwad, S. Naik, N. Dhutre, S. Maniyar, and V. Kulkarni, “Parametric Analysis of Rotary Friction Welding Process Based On Comparative Study between Mild Steel and Stainless Steel 304,” Int. J. Res. Eng. Appl. Manag., vol. 5, no. special issue, pp. 224–228, 2019.
S. Zhang, F. Xie, X. Wu, J. Luo, W. Li, and X. Yan, “The Microstructure Evolution and Mechanical Properties of Rotary Friction Welded Duplex Stainless Steel Pipe,” Materials (Basel)., vol. 16, no. 9, 2023, doi: 10.3390/ma16093569.
A. M. Mahajan, N. K. Babu, M. K. Talari, A. U. Rehman, and P. Srirangam, “Effect of Heat Treatment on the Microstructure and Mechanical Properties of Rotary Friction Welded AA7075 and AA5083 Dissimilar Joint,” Materials (Basel)., vol. 16, no. 6, 2023, doi: 10.3390/ma16062464.
A. J. Hassan, B. Cheniti, B. Belkessa, T. Boukharouba, D. Miroud, and N. E. Titouche, “Metallurgical Investigation of Direct Drive Friction Welded Joint for Austenitic Stainless Steel,” Acta Metall. Slovaca, vol. 29, no. 2, pp. 88–92, Jun. 2023, doi: 10.36547/ams.29.2.1802.
A. Dehghan-Manshadi, M. R. Barnett, and P. D. Hodgson, “Recrystallization in AISI 304 austenitic stainless steel during and after hot deformation,” Mater. Sci. Eng. A, vol. 485, no. 1–2, pp. 664–672, 2008.
M. S. Anwar, R. R. Widjaya, L. B. A. Prasetya, A. A. Arfi, E. Mabruri, and E. S. Siradj, “Effect of Grain Size on Mechanical and Creep Rupture Properties of 253 MA Austenitic Stainless Steel,” Metals (Basel)., vol. 12, no. 5, p. 820, 2022.
R. Ke, C. Hu, M. Zhong, X. Wan, and K. Wu, “Grain refinement strengthening mechanism of an austenitic stainless steel: Critically analyze the impacts of grain interior and grain boundary,” J. Mater. Res. Technol., vol. 17, pp. 2999–3012, 2022.
DOI: http://dx.doi.org/10.30811/jpl.v22i2.4978
Refbacks
- There are currently no refbacks.
![Creative Commons License](http://licensebuttons.net/l/by-sa/4.0/88x31.png)
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Ciptaan disebarluaskan di bawah Lisensi Creative Commons Atribusi-BerbagiSerupa 4.0 Internasional.
Mailing Address:
Jl. Banda Aceh-Medan
Km. 280,3, Buketrata, Mesjid Punteut, Blang Mangat,
Kota Lhokseumawe, 24301
Propinsi Aceh,
Indonesia