The Simulation Of Drop-Weight Impact Test On Ramie-Eglass Hybrid Fiber Composite For Jaloe Kayoh Wall Material

akram Tamlicha; Samsul Rizal; Iskandar Hasanuddin; Muhamad Mat Noor; Ikramullah Ikramullah; Nazaruddin Nazaruddin

doi:10.30811/jpl.v22i1.4645

The Simulation Of Drop-Weight Impact Test On Ramie-Eglass Hybrid Fiber Composite For Jaloe Kayoh Wall Material

akram Tamlicha, Samsul Rizal, Iskandar Hasanuddin, Muhamad Mat Noor, Ikramullah Ikramullah, Nazaruddin Nazaruddin

Abstract

The purpose of this study is to simulate drop-weight impact tests on hybrid fibre composites made of ramie and Eglass, which are used to make the traditional Acehnese boat wall material for jaloe kayoh. Using composites of ramie-Eglass fiber hybrid in the construction of jaloe kayoh wall material will significantly enhance the strength, durability, and sustainability of traditional Acehnese boats. The simulation was carried out using the finite element method approach using the Abaqus software. Three distinct laminate layer configurations—three layers (GRG), five layers (GRGRG), and six layers (GRGGRG)—with alternating Eglass and ramie fibres make up the test specimens. The ends of the specimen are set with fixed support to ensure boundary conditions, which limit all active structural degrees of freedom on all sides of the specimen. According to simulation results, the specimen with six laminate layers, measuring 12.498 mm, had the largest displacement. The specimen with six laminate layers has the highest stress concentration, measured at 560.6 MPa, while the specimen with three layers has the highest strain concentration, measured at 0.023. Its indicating that the lamina variation can influence the structural performance of the jaloe kayoh material. This research contributes to understanding the potential of ramie-Eglass hybrid fiber composites to enhance the safety and durability of traditional vessels such as jaloe kayoh. The implications of the results can serve as a foundation for the development of superior structural materials in the future.

Keywords

Jaloe kayoh, hybrid composite, ramie-Eglass fiber, drop-weight impact testing.

Full Text:

PDF

References

A. Akram, I. Hasanuddin, N. Nazaruddin, R. Putra, and M. M. Noor, “Mechanical behavior of hybrid glass Fiber-Jute reinforced with polymer composite for the wall of the Acehnese boat ‘Jalo Kayoh,’” in IOP Conference Series: Materials Science and Engineering, Institute of Physics Publishing, Jul. 2019. doi: 10.1088/1757-899X/523/1/012076.

R. Giridharan, “Preparation and property evaluation of Glass/Ramie fibers reinforced epoxy hybrid composites,” Compos B Eng, vol. 167, pp. 342–345, Jun. 2019, doi: 10.1016/J.COMPOSITESB.2018.12.049.

S. N. A. Safri, M. T. H. Sultan, M. Jawaid, and K. Jayakrishna, “Impact behaviour of hybrid composites for structural applications: A review,” Compos B Eng, vol. 133, pp. 112–121, Jan. 2018, doi: 10.1016/J.COMPOSITESB.2017.09.008.

M. Ramesh, L. Rajeshkumar, and D. Balaji, “Mechanical and Dynamic Properties of Ramie Fiber-Reinforced Composites,” Mechanical and Dynamic Properties of Biocomposites, pp. 275–291, Jan. 2021, doi: 10.1002/9783527822331.CH15.

S. A. Hassan et al., “Effect of fiber stacking sequence and orientation on quasi- static indentation properties of sustainable hybrid carbon/ramie fiber epoxy composites,” Current Research in Green and Sustainable Chemistry, vol. 5, p. 100284, Jan. 2022, doi: 10.1016/J.CRGSC.2022.100284.

P. Manik, T. Tuswan, F. A. O. Rahardjo, and S. Misbahudin, “Mechanical Properties Evaluation of Laminated Composites of Petung Bamboo (Dendrocalamus asper) and Coconut Coir Fiber as Ship Construction Components,” Pomorstvo, vol. 37, no. 1, pp. 75–85, Jun. 2023, doi: 10.31217/P.37.1.7.

Y. Y. Sunarya, H. Hendriyana, and I. N. Darmaputra, “Exploring Indigenous Material of Thorny Pandanus Pangandaran as Indonesian Traditional Craft in the Creative Context,” pp. 38–42, Jul. 2020, doi: 10.5220/0009323500380042.

K. : Jurnal et al., “A Bamboo-Hybrid-Slat Laminate of Fishing Boat: Materials Selection, Scantling Calculation and Construction Cost,” Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan, vol. 18, no. 3, pp. 151–159, Nov. 2021, doi: 10.14710/KAPAL.V18I3.41559.

M. Ali Jakhrani et al., “The Utilization of Agave Cantula Roxb as Composite Strength on Fishing Boat Hull,” IOP Conf Ser Mater Sci Eng, vol. 1088, no. 1, p. 012101, Feb. 2021, doi: 10.1088/1757-899X/1088/1/012101.

V. Chauhan, T. Kärki, and J. Varis, “Review of natural fiber-reinforced engineering plastic composites, their applications in the transportation sector and processing techniques,” Journal of Thermoplastic Composite Materials, vol. 35, no. 8, pp. 1169–1209, Aug. 2022, doi: 10.1177/0892705719889095/ASSET/IMAGES/LARGE/10.1177_0892705719889095-FIG7.JPEG.

“Maritime Rituals as Community Practices.” [Online]. Available: https://webinar.unesco-ichcap.org/portfolio-items/

F. M. AL-Oqla, M. T. Hayajneh, and N. Nawafleh, “Advanced synthetic and biobased composite materials in sustainable applications: a comprehensive review,” Emergent Mater, vol. 6, no. 3, pp. 809–826, Jun. 2023, doi: 10.1007/S42247-023-00478-Z/METRICS.

T. Akram, R. Samsul, H. Iskandar, M. M. Noor, and Nazaruddin, “Finite Element Analysis of the Jaloe kayoh Boat Structure with Load Variations by Using E-Glass and Ramie Fiber Composite Materials,” Key Eng Mater, vol. 930, pp. 61–70, 2022, doi: 10.4028/P-70C7JL.

M. J. Suriani et al., “Critical review of natural fiber reinforced hybrid composites: Processing, properties, applications and cost,” Polymers, vol. 13, no. 20. MDPI, Oct. 01, 2021. doi: 10.3390/polym13203514.

M. J. Suriani, H. Z. Rapi, R. A. Ilyas, M. Petrů, and S. M. Sapuan, “Delamination and Manufacturing Defects in Natural Fiber-Reinforced Hybrid Composite: A Review,” Polymers 2021, Vol. 13, Page 1323, vol. 13, no. 8, p. 1323, Apr. 2021, doi: 10.3390/POLYM13081323.

N. Nazaruddin, A. Akram, I. Hasanuddin, M. Iqbal, R. Kurniawan, and R. Putra, “Mechanical properties of glass fiber reinforced polyester resin for use as the wall of the Acehnese boat ‘Thep-Thep,’” IOP Conf Ser Mater Sci Eng, vol. 523, no. 1, p. 012080, May 2019, doi: 10.1088/1757-899X/523/1/012080.

N. M. Nurazzi et al., “A review on mechanical performance of hybrid natural fiber polymer composites for structural applications,” Polymers, vol. 13, no. 13. MDPI AG, Jul. 01, 2021. doi: 10.3390/polym13132170.

F. Ozdil and L. A. Carlsson, “Beam analysis of angle-ply laminate DCB specimens,” Compos Sci Technol, vol. 59, no. 2, pp. 305–315, Feb. 1999, doi: 10.1016/S0266-3538(98)00069-4.

N. An, Q. Jia, H. Jin, X. Ma, and J. Zhou, “Multiscale modeling of viscoelastic behavior of unidirectional composite laminates and deployable structures,” Mater Des, vol. 219, p. 110754, Jul. 2022, doi: 10.1016/J.MATDES.2022.110754.

N. R. J. Hynes, R. Sankaranarayanan, J. S. Kumar, S. M. Rangappa, and S. Siengchin, “Mechanical Behavior of Synthetic/Natural Fibers in Hybrid Composites,” Hybrid Fiber Composites, pp. 129–146, Oct. 2020, doi: 10.1002/9783527824571.CH8.

N. M. Hassan, Z. Bahroun, A. Mohamed, A. Baker, K. Jijakli, and A. Saqr, “Designing an impact resistant sandwich panel composite using struct based structures,” Compos Struct, vol. 258, p. 113432, Feb. 2021, doi: 10.1016/J.COMPSTRUCT.2020.113432.

B. S. Lazarus, A. Velasco-Hogan, T. Gómez-del Río, M. A. Meyers, and I. Jasiuk, “A review of impact resistant biological and bioinspired materials and structures,” Journal of Materials Research and Technology, vol. 9, no. 6, pp. 15705–15738, Nov. 2020, doi: 10.1016/J.JMRT.2020.10.062.

J. M. McCracken, B. R. Donovan, and T. J. White, “Materials as Machines,” Advanced Materials, vol. 32, no. 20, p. 1906564, May 2020, doi: 10.1002/ADMA.201906564.

G. He, Y. Liu, T. E. Lacy, and M. F. Horstemeyer, “A historical review of the traditional methods and the internal state variable theory for modeling composite materials,” Mechanics of Advanced Materials and Structures, vol. 29, no. 18, pp. 2617–2638, 2022, doi: 10.1080/15376494.2021.1872124.

A. Tamlicha et al., “Optimization of the jaloe kayoh seat design using the quality function deployment (QFD) method based on anthropometric measurements of the Acehnese Society,” Jurnal Polimesin, vol. 21, no. 2, pp. 192–198, Apr. 2023, doi: 10.30811/JPL.V21I2.3202.

V. Mahesh, S. Joladarashi, and S. M. Kulkarni, “A comprehensive review on material selection for polymer matrix composites subjected to impact load,” Defence Technology, vol. 17, no. 1, pp. 257–277, Feb. 2021, doi: 10.1016/J.DT.2020.04.002.

I. S. Abbood, S. A. Odaa, K. F. Hasan, and M. A. Jasim, “Properties evaluation of fiber reinforced polymers and their constituent materials used in structures – A review,” Mater Today Proc, vol. 43, pp. 1003–1008, Jan. 2021, doi: 10.1016/J.MATPR.2020.07.636.

C. W. Isaac and C. Ezekwem, “A review of the crashworthiness performance of energy absorbing composite structure within the context of materials, manufacturing and maintenance for sustainability,” Compos Struct, vol. 257, p. 113081, Feb. 2021, doi: 10.1016/J.COMPSTRUCT.2020.113081.

T. Abirami, G. Murali, K. Saravana Raja Mohan, M. P. Salaimanimagudam, P. Nagaveni, and P. Bhargavi, “Multi-layered two stage fibrous composites against low-velocity falling mass and projectile impact,” Constr Build Mater, vol. 248, p. 118631, Jul. 2020, doi: 10.1016/J.CONBUILDMAT.2020.118631.

R. Xu et al., “Data-driven multiscale finite element method: From concurrence to separation,” Comput Methods Appl Mech Eng, vol. 363, p. 112893, May 2020, doi: 10.1016/J.CMA.2020.112893.

X. Liu, C. A. Featherston, and D. Kennedy, “Buckling optimization of blended composite structures using lamination parameters,” Thin-Walled Structures, vol. 154, p. 106861, Sep. 2020, doi: 10.1016/J.TWS.2020.106861.

R. L. Mott and J. A. Untener, “Applied Strength of Materials; Seventh Edition.”

J. Galos, “Thin-ply composite laminates: a review,” Compos Struct, vol. 236, p. 111920, Mar. 2020, doi: 10.1016/J.COMPSTRUCT.2020.111920.

W. Chen, W. He, N. Luo, Y. Tang, Z. Chen, and B. Jiang, “Effect of layer thickness on the enhanced strength and ductility of laminated Ti/Al composite,” Materials Science and Engineering: A, vol. 859, p. 144230, Nov. 2022, doi: 10.1016/J.MSEA.2022.144230.

B. R. N. Murthy, R. Beedu, R. Bhat, N. Naik, and P. Prabakar, “Delamination assessment in drilling basalt/carbon fiber reinforced epoxy composite material,” Journal of Materials Research and Technology, vol. 9, no. 4, pp. 7427–7433, Jul. 2020, doi: 10.1016/J.JMRT.2020.05.001.

M. Arena and M. Viscardi, “Strain state detection in composite structures: Review and new challenges,” Journal of Composites Science, vol. 4, no. 2. MDPI AG, 2020. doi: 10.3390/jcs4020060.

D. Li, “Layerwise Theories of Laminated Composite Structures and Their Applications: A Review,” Archives of Computational Methods in Engineering, vol. 28, no. 2, pp. 577–600, Mar. 2021, doi: 10.1007/S11831-019-09392-2/METRICS.

M. Ramesh, L. Rajeshkumar, and D. Balaji, “Influence of Process Parameters on the Properties of Additively Manufactured Fiber-Reinforced Polymer Composite Materials: A Review,” J Mater Eng Perform, vol. 30, no. 7, pp. 4792–4807, Jul. 2021, doi: 10.1007/S11665-021-05832-Y/METRICS.

DOI: http://dx.doi.org/10.30811/jpl.v22i1.4645