The effect of 3D printing parameters on the tensile strength of acrylonitrile butadiene styrene filament for designing CNC router machine gears

Lazuardi Lazuardi; Muhammad Akhlis Rizza

doi:10.30811/jpl.v21i5.4045

The effect of 3D printing parameters on the tensile strength of acrylonitrile butadiene styrene filament for designing CNC router machine gears

Lazuardi Lazuardi, Muhammad Akhlis Rizza

Abstract

Print parameters are factors that influence the mechanical strength of 3D printed objects. Based on a literature review, the parameters of layer thickness, printing speed, and fill geometry percentage value influence the mechanical strength of 3D printed objects. This study focuses on a combination of robust 3D printing parameters for designing CNC router machine gears. The purpose of this research was to determine the effect of printing parameters on the mechanical strength of tensile loads on 3D printed objects. From the experimental results, it was found that by providing a combination of layer thickness parameters, printing speed parameters, and fill percentage parameters, it has an effect on the mechanical strength resistance of 3D printed objects to accept tensile loads. From the research it was found that the ideal layer thickness parameter of 0.1 to 0.2 mm does not exceed half the size of the nozzle diameter of 0.4 mm to produce fine raster fibers. From the research it was found that the ideal speed parameter for printing gears with ABS filament material is at speed 30 mm/s to 50 mm/s to produce a stable raster fiber size and the percentage parameter of a good fill for printing gears is at a value of 20% to 40%. The results of the research found the best printing parameters for printing gears with a print parameter formula with a 3D print parameter formula layer height 0.15mm, gyroid infill 20%, with a speed of 30mm/s maximum tensile strength reaching 30.7 MPa with the results of wheel loading simulation analysis gear is able to withstand a maximum workload of 85 Kg

Keywords

Gears, 3D printing, filament, tensile stress, acrylonitrile butadiene styrenee

Full Text:

PDF

References

Ait-Mansour, I.; Kretzschmar, N.; Chekurov, S.; Salmi, M.; Rech, J. Design-dependent shrinkage compensation modeling and mechanical property targeting of metal FFF. Prog. Addit. Manuf. 2020, 5, 51–57.

Ali, Z.; Türeyen, E.B.; Karpat, Y.; Çakmakcı, M. Fabrication of polymer micro needles for transdermal drug delivery system using DLP based projection stereo-lithography. Procedia CIRP 2016, 42, 87–90.

Ahn, S.H.; Montero, M.; Odell, D.; Roundy, S.; Wright, P.K. Anisotropic material properties of fused deposition modeling ABS. Rapid Prototyp. J. 2002, 8, 248–257.

Brian, N.T.; Robert, S.; Scott, A.G. A review of melt extrusion additive manufacturing processes: I. Process design and modeling. Rapid Prototyp. J. 2014, 20, 192–204.

Bellini A, Güçeri S. Mechanical characterization of parts fabricated using fused deposition modeling. Rapid Prototyp J 2003.

Damon, J.; Dietrich, S.; Gorantla, S.; Popp, U.; Okolo, B.; Schulze, V. Process porosity and mechanical performance of fused filament fabricated 316L stainless steel. Rapid Prototyp. J. 2019, 25, 1319–1327.

Dawoud, M.; Taha, I.; Ebeid, S.J. Mechanical behaviour of ABS: An experimental study using FDM and injection moulding techniques. J. Manuf. Process. 2016, 21, 39–45.

Es-Said OS, Foyos J, Noorani R, Mendelson M, Macmoth R, Pregger BA (2000) Effect of layer orientation on mechanical properties of rapid prototyped samples. Mater Manuf Process J 5(1):107–122.

Fayazbakhsh, K.; Movahedi, M.; Kalman, J. The impact of defects on tensile properties of 3D printed parts manufactured by fused filament fabrication. Mater. Today Commun. 2019, 18, 140–148.

Frascio, M.; de Marques, E.A.S.; Carbas, R.J.C.; da Silva, L.F.M.; Monti, M.; Avalle, M. Review of Tailoring Methods for Joints with Additively Manufactured Adherends and Adhesives. Materials 2020, 13, 3949.

Guessasma, S.; Belhabib, S.; Nouri, H. Effect of printing temperature on microstructure, thermal behavior and tensile properties of 3D printed nylon using fused deposition modeling. J. Appl. Polym. Sci. 2021, 138, 50162.

Graupner N, Herrmann AS, Müssig J. Natural and man-made cellulose fibre reinforced poly(lactic acid) (PLA) composites: an overview about mechanical characteristics and application areas. Composites Part A 2009

Gibson I, Rosen DW, Stucker B. Additive manufacturing technologies: rapid prototyping to direct digital manufacturing. New York: Springer; 2010.

Gordeev, E.G.; Galushko, A.S.; Ananikov, V.P. Improvement of quality of 3D printed objects by elimination of microscopic structural defects in fused deposition modeling. PLoS ONE 2018, 13, e0198370.

Hofstätter, T.; Pedersen, D.B.; Tosello, G.; Hansen, H.N. State-of-the-art of fiber-reinforced polymers in additive manufacturing technologies. J. Reinf. Plast. Compos. 2017, 36, 1061–1073.

Hadi .S, Teknolofi Bahan . ANDI Yogyakartat : 2016.

Jaya Christiyan KG, Chandrasekhar U, Venkateswarlu K (2014) Influence of raster orientation and layer thickness on mechanical properties of ABS material using FDM process. Int J Adv Res Sci Eng 3:1–6

Joshi SC, Shcikh AA (2015) 3D printing in aerospace and its long-term sustainability. Virtual Phys Prokityping J 101175–101185

Liu, J.-L.; Feng, X.-Q.; Wang, G.; Yu, S.-W. Mechanisms of superhydrophobicity on hydrophilic substrates. J. Phys. Condens. Matter 2007, 19, 356002.

Liu, J.L.; Nie, Z.X.; Jiang, W.G. Deformation field of the soft substrate induced by capillary force. Phys. B Condens. Matter 2009, 404, 1195–1199.

Li L, Sun Q, Bellehumeur C, Gu P. Composite modeling and analysis for fabrication of FDM prototypes with locally controlled properties. J Manuf Process 2002

Letcher T (2014) Material property testing of 3D printed specimen in PLA on an entry level 3D printer. Int Mech Eng Congr Exposition Montreal IMECE 2:1–8

Linares-Alvelais, J.A.R.; Figueroa-Cavazos, J.O.; Chuck-Hernandez, C.; Siller, H.R.; Rodríguez, C.A.; Martínez-López, J.I. Hydrostatic high-pressure post-processing of specimens fabricated by DLP, SLA, and FDM: An alternative for the sterilization of polymer-based biomedical devices. Materials 2018, 11, 2540.

Mahamood, R.; Akinlabi, S.; Shatalov, M.; Murashkin, E.; Akinlabi, E. Additive Manufacturing / 3D Printing Technology: A Review. Ann. Dunarea Jos Univ. Galati. Fascicle XII Weld. Equip. Technol. 2019, 30.

Mohamed OA, Masood SH, Bhowmik JL (2015) Optimization of fused deposition modeling process parameters: a review of current research and future prospects. Adv Manuf 3:42–53

Oksman K, Skrifvars M, Selin JF. Natural fibers as reinforcement in polylactic acid (PLA) composites. Compos Sci Technol 2003;

Pan, A.Q.; Huang, Z.F.; Guo, R.J.; Liu, J. Effect of FDM Process on Adhesive Strength of Polylactic Acid(PLA) Filament. Key Eng. Mater. 2016, 667, 181–186.

Percoco, G.; Arleo, L.; Stano, G.; Bottiglione, F. Analytical model to predict the extrusion force as a function of the layer height, in extrusion based 3D printing. Addit. Manuf. 2021, 38, 101791.

Petrovic V, Gonzalez JVH, Ferrando OJ, Gordillo JD, Puchades JRB, Griñan LP. Additive layered manufacturing: sectors of industrial application shown through case studies. Int J Prod Res 2011 2002;8(4):248–57.

Pawar, S.; Dolas, D. Experimental Investigation and Empirical Modeling of FDM Process for Tensile Strength Improvement. Lect. Notes Mech. Eng. 2020, 3, 371–378.

Ramya A, Vanapalli SL 3D printing technologies in various applications. Int J Mech

Savu, I.D.; Savu, S.V.; Simion, D.; Sîrbu, N.-A.; Ciornei, M.; Ratiu, S.A. PP in 3D Printing–Technical and Economic Aspects. Mater. Plast. 2019, 56, 931.

Shahrubudin, N.; Lee, T.C.; Ramlan, R. An Overview on 3D Printing Technology: Technological, Materials, and Applications. Procedia Manuf. 2019, 35, 1286–1296.

Sebastian Wernicke a, Marlon Hahn a, Andreas Detzel a, (2021) Force reduction by electrical assistance in incremental sheet-bulk metal forming of gears nstitute of Forming Technology and Lightweight Construction, TU Dortmund University, Baroper Str. 303, D-44227, Dortmund, Germany

Sood, A.K.; Ohdar, R.K.; Mahapatra, S.S. Parametric appraisal of mechanical property of fused deposition modelling processed parts. Mater. Des. 2010, 31, 287–295.

Schmid, M.; Amado, A.; Wegener, K. Polymer powders for selective laser sintering (SLS). In Proceedings of the AIP Conference proceedings, Cleveland, OH, USA, 6–12 June 2014; AIP Publishing LLC: Melville, NY, USA, 2015; Volume 1664, p. 160009.

Syahrum, Metodologi Penelitian. Citapustaka Media, Bandung : 2012

Tofail, S.A.M.; Koumoulos, E.P.; Bandyopadhyay, A.; Bose, S.; O’Donoghue, L.; Charitidis, C. Additive manufacturing: Scientific and technological challenges, market uptake and opportunities. Mater. Today 2018, 21, 22–37.

Tymrak BM, Kreiger M, Pearce JM (2014) Mechanical properties of components fabricated with open-source 3D printers under realistic environmental conditions. Mat Des J 58:242–246

Ullu E, Korkmaz E, Yay K. Ozdoganlar OB, Kara LB (2015) Enhancing the structural performance of additively manufactured objects through build orientation optimization. J Mech Des 137:111410–111419

Vega, V.; Clements, J.; Lam, T.; Abad, A.; Fritz, B.; Ula, N.; Es-Said, O.S. The effect of layer orientation on the mechanical properties and microstructure of a polymer. J. Mater. Eng. Perform. 2011, 20, 978–988.

Wu Chen, Xiaofei He, Wenchao Yu, Maoqiu Wang, and Kefu Yao (2021) Microstructure, Hardness, and Tensile Properties of Vacuum Carburizing Gear Steel. School of Materials Science and Engineering, Tsinghua University, Beijing 100084, China; chenwu15@mails.tsinghua.edu.cn (W.C.); kfyao@mail.tsinghua.edu.cn (K.Y).

Yan Y, Li S, Zhand R, Lin F, Wu R, Lu Q, Xiong Z, Wang X (2009) Rapid prototyping and manufacturing technology principle, representative technics, applications, and development trends. Tsinghua Science and Technology, pp 1–12.

Zarringhalam, H.; Hopkinson, N.; Kamperman, N.F.; de Vlieger, J.J. Effects of processing on microstructure and properties of SLS Nylon 12. Mater. Sci. Eng. A 2006, 435–436, 172–180.

DOI: http://dx.doi.org/10.30811/jpl.v21i5.4045