Implementasi Mini CNC Router 3 Axis untuk Pembuatan Huruf dan Gambar Berbasis GRBL 3.6.1

Roswaldi Sk, Julsam Julsam, Kartika Kartika, Alno Fendri, Mulyadi Mulyadi

Sari


This article provides a treasure trove of control system science in order to remember the competitiveness of SME production in Indonesia. Many SME entrepreneurs are still unfamiliar in using CNC Machines to work on SME practitioners. CNC machines can be used to make letters and drawings. The CNC machine uses three stepper motors and one dc motor with high speed, which functions for spindder, and as a series of electronics uses arduino and sheel stepper motor drivers. These three stepper motors are controlled with GRBL 3.6.1 and Easel software. After testing, an error was obtained on the x-axis x-engraved 1.2%. The y axis is 1.5% and the z axis is 5.8%. While errors in making images / logos by 2%.


Kata Kunci


3 Axis Mini CNC Router Machine; GRBL 3.6.1 Software; Easel Software and Stepper motors

Teks Lengkap:

PDF

Referensi


S. M. Metev and V. P. Veiko, Laser Assisted Microtechnology, 2nd ed., R. M. Osgood, Jr., Ed. Berlin, Germany: Springer-Verlag, 1998.

R. Choudhary, Sambhav, S. D. Titus, P. Akshaya, J. A. Mathew, dan N. Balaji, “CNC PCB milling and wood engraving machine,” in 2017 International Conference On Smart Technologies For Smart Nation (SmartTechCon), 2017, hal. 1301–1306.

A. A. Perez dan F. J. A. Sanchez, “Prototype for the mechanical engraver of aluminum plates assisted by computer,” in International Conference on Electronics, Communications and Computers, 2004. CONIELECOMP 2004., 2004.

S. Guvercin, R. Suliyev, dan G. Tolebi, “Design of automatic engraving machine controlled via computer,” in 2015 Twelve International Conference on Electronics Computer and Computation (ICECCO), 2015, hal. 1–3.

M. T. Shahid, M. A. Khan, dan M. Z. Khan, “Design and Development of a Computer Numeric Controlled 3D Printer, Laser Cutter and 2D Plotter all in one machine,” in 2019 16th International Bhurban Conference on Applied Sciences and Technology (IBCAST), 2019, hal. 569–575.

Sudarno, Martono, dan S. Mauladin, “Rancang Bangun Mesin CNC Router Berbasis Arduino,” POLITEKNOSAINS, vol. Vol. XV, no. 2, hal. 51–55, 2016.

I. S. Harrizal, Syafri, dan A. Prayitno, “Rancang Bangun Sistem Kontrol Mesin Cnc Milling3 Axis menggunakan Close Loop System,” JOM FTEKNIK, vol. 4, no. 2, hal. 1–8, 2017.

Sahrul, “Motor Stepper: Teknologi, Metoda Dan Rangkaian Kontrol,”Univ. Komput. Indones. Bandung, hal. 187–202, 2019.

K. Abdul, Panduan Praktis Mempelajari Aplikasi Mikrokontroler dan Pemrogramannya Menggunakan Arduino, Andi. Yokyakarta: Andi, 2013.

A. A. Fuadzi, I. Santosa, dan G. R. Wilis, “Instrumen Kendali Mesin Cnc Portable Berbasis Microcontroller Arduino Dan Modul Cnc Shield,”in 1st Mechanical Engineering National Converence, 2018, 2018, hal.87–96.

Nn, “A4988 Stepper Motor Driver Carrier, Black Edition,” Pololu Robotic & Electronics, 2019.


Refbacks

  • Saat ini tidak ada refbacks.


##submission.copyrightStatement##

##submission.license.cc.by-sa4.footer##

Creative Commons License

Prosiding Seminar Nasional Politeknik Negeri Lhokseumawe is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License

© 2017 All rights reserved |Seminar nasional Politeknik Negeri Lhokseumawe p-ISSN:2598-3954.

.