Effects of cooling time, injection pressure, and material type on the mechanical properties of ballun insulator products in injection molding

Muhammad Rifqi Sepvian; Sugeng Hadi Susilo

doi:10.30811/jpl.v24i3.8956

Effects of cooling time, injection pressure, and material type on the mechanical properties of ballun insulator products in injection molding

Muhammad Rifqi Sepvian, Sugeng Hadi Susilo

Abstract

A major challenge in injection molding is the instability of mechanical properties in products due to suboptimal process parameter settings, which necessitates identifying the optimal parameter combination to achieve adequate tensile strength and hardness. This study aims to evaluate the effects of cooling time, injection pressure, and material type on the tensile strength and hardness of ballun insulator products produced by injection molding. Two thermoplastic materials, Polypropylene (PP) and High-Density Polyethylene (HDPE), were selected due to their different molecular structures and crystallization behavior, both of which influence mechanical performance. The materials were processed under varying cooling times (20, 25, 30, and 35 s) and injection pressures (24, 27, 30, 33, and 36 bar). The novelty of this study lies in the comparative evaluation of PP and HDPE under identical process conditions for ballun insulator applications. The results showed that higher injection pressure improved mold-filling and molecular chain compaction, leading to increased tensile strength, while longer cooling time promoted more controlled crystallization and improved surface hardness. PP exhibited higher tensile strength due to its stiffer molecular structure, achieving a maximum tensile strength of 0.031 MPa at 36 bars. In contrast, HDPE showed higher hardness due to its denser crystalline structure, reaching 69.75 HD at 35 s cooling time. These findings indicate that material-specific optimization of injection molding parameters is important for achieving consistent mechanical properties and dimensional stability in ballun insulator products.

Keywords

Cooling Time; Injection Pressure; HDPE; PP; Ballun Insulator; Injection Molding; Hardness

Full Text:

PDF

References

GO Edah, JO Atiba, and OSI Fayomi, “Advancements in fiber -reinforced polymers: Properties, applications (A mini review),” Jul. 01, 2025, Elsevier BV doi: 10.1016/j.nxmate.2025.100743.

NE Ajayi, S. Rusnakova, AE Ajayi, RO Ogunleye, SO Agu, and AN Amenaghawon, “A comprehensive review of natural fiber reinforced Polymer composites as emerging materials for sustainable applications,” Apr. 01, 2025, Elsevier Ltd. doi : 10.1016/j.apmt.2025.102666.

AO Stanley, S. Rusnáková, RO Ogunleye, and N.E. Ajayi, “Optimization of compression molding technology for laminar composites: An overview,” Next Research, vol. 2, no. 4, p. 101027, Dec. 2025, doi : 10.1016/j.nexres.2025.101027.

T. Wang, J. Huang, H. Fu, K. Yu, and S. Yao, “Influence of Process Parameters on Filling and Feeding Capacity during High-Pressure Die-Casting Process,” Applied Sciences (Switzerland), vol. 12, no. 9, May 2022, doi: 10.3390/app12094757.

HA HamaSalih, RM Abdalrahman, and S. Rostam, “Optimizing the blending ratio and processing parameters for ternary blends of recycled polypropylene with recycled high and virgin linear low-densities polyethylene,” Results in Engineering, vol. 18, June. 2023, doi: 10.1016/j.rineng.2023.101171.

J. Vanek, M. Ovsik, M. Stanek, J. Hanzlik, and V. Pata, “Study of Injection Molding Process to Improve Geometrical Quality of Thick-Walled Polycarbonate Optical Lenses by Reducing Sink Marks,” Polymers (Basel)., vol. 16, no. 16, Aug. 2024, doi : 10.3390/polym16162318.

M. Tan, S. Peng, Y. Huo, and M. Li, “Multi-Objective Optimization of Injection Molding Parameters for Manufacturing Thin-Walled Composite Connector Terminals,” Materials, vol. 17, no. 16, Aug. 2024, doi: 10.3390/ma17163949.

P. Zengeya, K. Mao, and V. Goodship , “The effects of cooling rate (mold temperature) on HDPE gears produced through injection molding,” Wear, vol. 530–531, Oct. 2023, doi: 10.1016/j.wear.2023.205000.

K. Fucikova, M. Ovsik, A. Cesnek, A. Pis, J. Vanek, and M. Stanek, “Influence of Injection Molding Parameters and Distance from Gate on the Mechanical Properties of Injection-Molded Polypropylene,” Polymers (Basel), vol. 17, no. 8, Apr. 2025, doi: 10.3390/polym17081012.

J. Wang, Q. Mao, N. Jiang, and J. Chen, “Effects of injection molding parameters on properties of insert-injection molded polypropylene single-polymer composites,” Polymers (Basel). , vol. 14, no. 1, Jan. 2022, doi: 10.3390/polym14010023.

MMA Nassar, KI Alzebdeh , MMM Alsafy, and M. Jawaid, “Optimization and predictive modeling of chemically crosslinked recycled PE/PP blends for enhanced mechanical properties,” Results in Engineering, vol. 28, Dec. 2025, doi: 10.1016/j.rineng.2025.108360.

Y. Li et al., “Modified lignin-based intumescent flame retardant's effect on flame retardancy, mechanical and electrical properties of HDPE material for cable sheathing,” Polym. Test., vol. 135, Jun. 2024, doi: 10.1016/j.polymertesting.2024.108464.

E. Mejia, N. Cherupurakal, AHI Mourad, S. Al Hassanieh, and M. Rabia, “Effect of processing techniques on the microstructure and mechanical performance of high‐density polyethylene,” Polymers (Basel)., vol. 13, no. 19, Oct. 2021, doi : 10.3390/polym13193346.

GY Liou et al., “Optimize Injection-Molding Process Parameters and Build an Adaptive Process Control System Based on Nozzle Pressure Profile and Clamping Force,” Polymers (Basel)., vol. 15, no. 3, Feb. 2023, doi: 10.3390/polym15030610.

M.A. Sharaf and A. Kloczkowski, “Evolution of the Deformation- and Flow-Induced Crystallization and Characterization of the Microstructure of a Single Spherulite, Lamella, and Chain of Isotactic Polypropylene,” Jan. 01, 2024, John Wiley and Sons Inc. doi : 10.1002/macp.202300203.

SMS Mukras, “Experimental-based optimization of injection molding process parameters for short product cycle time,” Advances in Polymer Technology, vol. 2020, 2020, doi: 10.1155/2020/1309209.

JH Park and SK Kim, “Expansion Injection Molding Process Using Clamping Force for Melt Compression,” Polymers (Basel)., vol. 16, no. 3, Feb. 2024, doi: 10.3390/polym16030424.

Y. Hu et al., “Influence of Cooling Rate on Crystallization Behavior of Semi-Crystalline Polypropylene: Experiments and Mathematical Modeling,” Polymers (Basel), vol. 14, no. 17, Sept. 2022, doi: 10.3390/polym14173646.

W. Yu et al., “Study on the Influence of Microinjection Molding Processing Parameters on Replication Quality of Polylactic Acid Microneedle Array Product,” Polymers (Basel)., vol. 15, no. 5, March. 2023, doi: 10.3390/polym15051199.

A. Rajabi, M. Kadkhodayan, and S. Alamzadeh, “Effects of Injection Molding Parameters on the Mechanical Properties and Surface Roughness of Polypropylene Parts,” International Journal of Engineering, vol. 28, no. 1, pp. 138–145, 2015, doi: 10.5829/idosi.ije.2015.28.01a. 18

DOI: http://dx.doi.org/10.30811/jpl.v24i3.8956