The effect of heat input on defect formation, macrostructure, microstructure and hardness in AA 1100 aluminum weld joints using the GMAW process

Rizki Dwi Ardika; Ilham Sulthoni; Munaji Munaji; Yoyok Winardi; Muizuddin Azka

doi:10.30811/jpl.v24i2.8632

The effect of heat input on defect formation, macrostructure, microstructure and hardness in AA 1100 aluminum weld joints using the GMAW process

Rizki Dwi Ardika, Ilham Sulthoni, Munaji Munaji, Yoyok Winardi, Muizuddin Azka

Abstract

AA 1100 aluminum is widely used in industrial applications due to its low density and good corrosion resistance; however, welding defects such as porosity and changes in mechanical properties often occur during Gas Metal Arc Welding (GMAW). One of the most influential parameters on weld quality is the welding current. This study analyzes the effect of welding current variations on the physical and mechanical properties of AA 1100 GMAW welded joints using ER 5356 filler wire. Welding was carried out at currents of 100 A, 130 A, and 160 A using argon shielding gas. The welded joints were evaluated by visual inspection, macrostructure observation, microstructure analysis, and Vickers microhardness testing. The test results showed that increasing the welding current resulted in wider weld beads, increased porosity and spatter defects, as well as coarser grain structures in the heat-affected zone (HAZ) and weld metal. The lowest porosity and spatter occurred at 100 A, while the highest porosity and spatter occurred at 160 A. This was due to excessive heat input and hydrogen trapping. Microstructural analysis revealed the presence of FeAl₃ intermetallic phases dispersed within the aluminum matrix. The highest hardness value was found in the weld metal region at 100 A, which was caused by the finer grain size and the strengthening effect of Mg from the ER 5356 filler. Overall, this study confirmed that the welding current significantly affects the defect formation, microstructural evolution, and hardness distribution of GMAW AA 1100 weld joints.

Keywords

Aluminum alloy; welding deffects; porosity; current; Gas Metal Arc Welding (GMAW)

Full Text:

PDF

References

M. Dada and P. Popoola, “Recent advances in joining technologies of aluminum alloys: a review,” Discov. Mater., vol. 4, no. 1, p. 86, 2024. doi: 10.1007/s43939-024-00155-w

C. Zhang, M. Gao, and X. Zeng, “Journal of Materials Processing Technology Effect of microstructural characteristics on high cycle fatigue properties of laser-arc hybrid welded AA6082 aluminum alloy,” J. Mater. Process. Tech., vol. 231, pp. 479–487, 2016, doi: 10.1016/j.jmatprotec.2016.01.019.

Y. Han, S. Xue, R. Fu, L. Lin, Z. Lin, Y. Pei, and H. Sun, “Influence of hydrogen embrittlement on impact property and microstructural characteristics in aluminum alloy weld,” Vacuum, vol. 172, no. November 2019, pp. 1–8, 2020, doi: 10.1016/j.vacuum.2019.109073.

D. Y. Kim, I. Hwang, G. Jeong, M. Kang, D. Kim, J. Seo, and Y. M. Kim, “Effect of porosity on the fatigue behavior of gas metal arc welding lap fillet joint in GA 590 MPa steel sheets,” Metals (Basel)., vol. 8, no. 4, 2018, doi: 10.3390/met8040241.

M. Chludzinski, L. Garcia-Sesma, O. Zubiri, N. Rodriguez, and E. Aldanondo, “Investigation of the Effects of Gas Metal Arc Welding and Friction Stir Welding Hybrid Process on AA6082-T6 and AA5083-H111 Aluminum Alloys,” Metals (Basel)., vol. 15, no. 9, p. 1005, 2025.

M. Orlando, M. De Maddis, V. Razza, and V. Lunetto, “Non-destructive detection and analysis of weld defects in dissimilar pulsed GMAW and FSW joints of aluminium castings and plates through 3D X-ray computed tomography,” Int. J. Adv. Manuf. Technol., vol. 132, no. 5, pp. 2957–2970, 2024, doi: 10.1007/s00170-024-13576-x.

D. Zhao, M. Ivanov, Y. Wang, and W. Du, “Welding quality evaluation of resistance spot welding based on a hybrid approach,” J. Intell. Manuf., vol. 32, no. 7, pp. 1819–1832, 2021.

C. Chen, G. Sun, W. Du, Y. Li, C. Fan, and H. Zhang, “Influence of heat input on the appearance, microstructure and microhardness of pulsed gas metal arc welded Al alloy weldment,” J. Mater. Res. Technol., vol. 21, pp. 121–130, 2022, doi: 10.1016/j.jmrt.2022.09.028.

J. C. Garcia-guerrero, F. F. Curiel-López, V. H. López-Morelos, J. J. Taha-Tijerina, T. J. Sánchez-Cruz, M. C. Ramirez-Lopez, E. Cortes-Carillo, and M. A. Quinones-Salinas, “Impact of Welding Parameters in the Porosity of a Dissimilar Welded Lap Joint of CP800-XPF1000 Steel Weldment by GMAW-P,” Metals., vol. 14 no. 3, p. 139, 2024, doi: 10.3390/met14030309

S. Kramer, V. Lubkowitz, M. Haas, J. Michel, C. Spurk, A. Olowinsky, G. A. Faria, M. Jarwitz, T. Graf, V. Schulze, and F. Zanger, “Investigation of the formation and reduction of hydrogen porosity during laser welding of additively manufactured AlSi10Mg parts,” Int J Adv Manuf Technol., vol 142, pp. 6105–6123, 2026. doi: 10.1007/s00170-025-17198-9.

K. Lu, J. Lin, Z. Chen, W. Wang, and H. Yang, “Safety assessment of incomplete penetration defects at the root of girth welds in pipelines,” Ocean Eng., vol. 230. December 2020, p. 109003, 2021, doi: 10.1016/j.oceaneng.2021.109003.

N. Cui, T. Zhao, Z. Wang, Y. Zhao, Y. Chao, H. Lin, D. Li, and J. Zhao, “Porosity evolution mechanisms, influencing factors, and ultrasonic-assisted regulation in joining high Mg-content aluminum alloys,” J. Mater. Process. Tech., vol. 336, no. October 2024, p. 118706, 2025, doi: 10.1016/j.jmatprotec.2024.118706.

A. M. Samuel, E. Samuel, and V. Songmene, “A Review on Porosity Formation in Aluminum-Based Alloys,” 2023.

N. Béraud, A. Chergui, M. Limousin, F. Villeneuve, and F. Vignat, “An indicator of porosity through simulation of melt pool volume in aluminum wire arc additive manufacturing,” vol. 1, pp. 1–8, 2022.

S. Huang, L. Xu, M. Lou, H. Chen, K. Zhang, and Y. Li, “Keyhole-induced pore formation mechanism in laser-MIG hybrid welding of aluminum alloy based on experiment and multiphase numerical model,” J. Mater. Process. Tech., vol. 314, no. August 2022, p. 117903, 2023, doi: 10.1016/j.jmatprotec.2023.117903.

K. J. Pranav, S. P. Sibi, and P. P. Jana, “Evolution of Fe-rich intermetallic phases in cast and wrought aluminium alloys: Microstructural insights and property correlations,” J. Alloys Compd., vol. 1042, no. September, p. 184101, 2025, doi: 10.1016/j.jallcom.2025.184101.

A. V. Jebaraj, K. V. V. Aditya, T. S. Kumar, L. Ajaykumar, and C. R. Deepak, “Mechanical and corrosion behaviour of aluminum alloy 5083 and its weldment for marine applications,” Mater. Today Proc., vol. 22, pp. 1470–1478, 2019, doi: 10.1016/j.matpr.2020.01.505.

H. Deng, Z. Liu, X. Wang, J. Ma, F. Han, and Z. Wang, “Effect of heat input on the microstructure and mechanical properties of the simulated coarse-grained heat-affected zone (CGHAZ) of novel twining-induced plasticity (TWIP) steel,” Mater. Today Commun., vol. 33, p. 104407, 2022.

C. Zhu, X. Tang, Y. He, F. Lu, and H. Cui, “Effect of preheating on the defects and microstructure in NG-GMA welding of 5083 Al-alloy,” J. Mater. Process. Technol., vol. 251, no. May 2017, pp. 214–224, 2018, doi: 10.1016/j.jmatprotec.2017.08.037.

K. G. Vorkachev, P. P. Stepanov, L. I. Éfron, M. M. Kantor, A. V Chastukhin, and S. V Zharkov, “Effect of microstructure on high-strength low-alloy steel welded joint toughness with simulation of heat-affected zone coarse-grained area,” Metallurgist, vol. 64, no. 9, pp. 875–884, 2021.

H. Qi, Q. Pang, W. Li, and S. Bian, “Effect of high welding heat input on the microstructure and low-temperature toughness of heat affected zone in magnesium-treated EH36 steel,” Sci. Rep., vol. 14, no. 1, p. 19459, 2024.

A. V. Jebaraj, K. V. V Aditya, T. S. Kumar, L. Ajaykumar, and C. R. Deepak, “ScienceDirect Mechanical and corrosion behaviour of aluminum alloy 5083 and its weldment for marine applications,” Mater. Today Proc., vol. 22, pp. 1470–1478, 2020, doi: 10.1016/j.matpr.2020.01.505.

R. D. Ardika, T. Triyono, N. Muhayat, and Triyono, “A review porosity in aluminum welding,” Procedia Struct. Integr., vol. 33, no. C, pp. 171–180, 2021, doi: 10.1016/j.prostr.2021.10.021.

N. Muhayat, R. D. Ardika, A. M. Kadir, E. P. Budiana, and T. Triyono, “Simultaneous Enhancement of Welder Health and Aluminum Weld Joint Quality Using Controlled Welding Room Condition,” 2024.

S. Senthilkumar, S. Manivannan, R. Venkatesh, and M. Karthikeyan, “Influence of heat input on the mechanical characteristics, corrosion and microstructure of ASTM A36 steel welded by GTAW technique,” Heliyon, vol. 9, no. 9, 2023.

DOI: http://dx.doi.org/10.30811/jpl.v24i2.8632