Optimization of cutting current in CNC plasma cutting for improved bracket fabrication quality

Ali Sai'in; Venditias Yudha; Luqman Al Huda; Zaenal Abidin; Hartanto Prawibowo

doi:10.30811/jpl.v24i2.8618

Optimization of cutting current in CNC plasma cutting for improved bracket fabrication quality

Ali Sai'in, Venditias Yudha, Luqman Al Huda, Zaenal Abidin, Hartanto Prawibowo

Abstract

CNC plasma cutting is widely used in metal fabrication due to its efficiency and versatility; however, parameter optimization is essential to ensure high-quality results. This study investigates the influence of CNC plasma cutting parameters affect the fabrication quality of Revo motorcycle brackets, which are essential for electric motor vehicle conversion. We conducted experiments on 6 mm thick low-carbon steel plates using a JIAXIN JX-1530 machine. The electric current was varied at 50, 52, 54, and 56 A. For each current level, four specimens were prepared and tested while keeping other parameters constant: a cutting speed of 600 mm/min, a gas pressure of 6 bar, and a torch distance of 1–2 mm. We assessed cut quality based on surface roughness (Ra) at two measurement points, dimensional accuracy relative to CAD design, and hardness variations in the Heat-Affected Zone (HAZ) and base material. The results showed that the best conditions were achieved at 50 A, 6 bar gas pressure, and a torch distance of 2 mm, resulting in an average Ra of 5.39 µm and a dimensional deviation of ±0.3 mm. Although increasing the current above 50 A improved HAZ hardness, it negatively impacted surface roughness and increased the risk of thermal defects. These findings indicate that the identified optimal parameters support the production of high-precision, cost-effective brackets.

Keywords

Plasma cutting; fabrication quality; motorcycle bracket; electric vehicle conversion; heat affected zone

Full Text:

PDF

References

Genna S, Patel S, Professor A. A Review on Laser Engraving Process Related papers A Review on Paramet ric Opt imizat ion of Laser Engraving using Fiber Laser on St eel IJSRD Journal Paramet ric Opt imizat ion of Laser Engraving Process for different Mat erial using Grey Relat ional Tec. IJSRD-International J Sci Res Dev 2015;3:2321–0613.

Jarosz K, Löschner P, Nies P. Effect of cutting speed on surface quality and heat-affected zone in laser cutting of 316L stainless steel. Int Conf Manuf Eng Mater 2016;149:155–62. https://doi.org/10.1016/j.proeng.2016.06.650.

Esrafili H, Amirabadi H, Akbari J, Jafarian F. A comparative study on laser-assisted and conventional machining characteristics of waspaloy. J Mater Res Technol 2025;37:4476–89. https://doi.org/10.1016/j.jmrt.2025.07.107.

Parthiban A, Chandrasekaran M, Muthuraman V, Sathish S. ScienceDirect Optimization of CO 2 Laser Cutting of Stainless Steel Sheet for Curved Profile. Mater Today Proc 2018;5:14531–8. https://doi.org/10.1016/j.matpr.2018.03.042.

Peko I. Analysis of the heat affected zone in plasma jet cutting process of the aluminium alloy EN AW 5083. Zast Mater 2019;60:174–81. https://doi.org/10.5937/zasmat1902174P.

Rahmawati AR, Anis S, Mesin PT, Semarang UN. PENGARUH KECEPATAN PEMOTONGAN DAN KETEBALAN BAHAN TERHADAP KEKERASAN DAN KEKASARAN PERMUKAAN BAJA AISI 1045 MENGGUNAKAN CNC PLASMA ARC CUTTING. J Din Vokasional Tek Mesin 2019;4:93–8.

Paper OS. EXPERIMENTAL RESEARCH OF THE PLASMA ARC CUTTING PROCESS. J Appl Eng Sci 2014;12:291–6. https://doi.org/10.5937/jaes12-6778.

Akkurt A. Engineering Science and Technology , an International Journal The effect of cutting process on surface microstructure and hardness of pure and Al 6061 aluminium alloy. Eng Sci Technol an Int J 2015;18:303–8. https://doi.org/10.1016/j.jestch.2014.07.004.

Rq R, Lq G, Dqg D. Optimization of Process Parameters in Plasma Arc Cutting of EN 31 Steel BAsed on MRR and Multiple Roughness Characterictics Using Grey Relational Analysis. Int Conferance Adv Manuf Mater Eng AMME 2014 2014;5:1550–9. https://doi.org/10.1016/j.mspro.2014.07.342.

Karthick M, Anand P, Meikandan M, Sekar S, Natrayan L, Bobe K. Optimization of Plasma Arc Cutting Parameters on Machining of Inconel 718 Superalloy. Hindawi J Nanomater 2022;2022. https://doi.org/10.1155/2022/7181075.

Peko I, Mari D, Nedi B, Samardži I. Modeling and Optimization of Cut Quality Responses in Plasma Jet Cutting of Aluminium Alloy EN AW-5083. MDPI Mater 2021.

Obanimomo KT, Lawal SA. Effect of Process Parameters on Surface Roughness and Kerf Width of Mild Steel during Plasma Arc Cutting Using Response Surface Methodology. FUOYE J Eng Technol 2020;5:67–71.

Hamid A, Novareza O, Widodo TD. OPTIMIZATION OF PROCESS PARAMETERS AND QUALITY RESULTS USING PLASMA ARC CUTTING IN ALUMINUM ALLOY. J Eng Manag Ind Syst VOL 7 NO 1 YEAR 2019 2019;7:7–14.

Górka J. The effect of air plasma cutting on the quality , structural transformations and changes in the chemical composition of structural steel. Arch Civ Mech Eng 2023;23:1–13. https://doi.org/10.1007/s43452-023-00763-y.

Using C, Arc P, Pam M, Abouzaid A. Influence of the Cutting Feed Rate on the Hardness and. MDPI Met 2023.

H SA. Optimization of plasma cutting parameters on HAZ and bevel angle for low carbon steel using response surface methodology Optimization of Plasma Cutting Parameters on HAZ and Bevel Angle for Low Carbon Steel Using Response Surface Methodology. AIP Conf Proc 2019;020019.

Susilo GB, Sasongko BT, Bhisma P, Wardhana W. ANALYSIS OF THE EFFECT OF CUTTING SPEED AND CURRENT ON SURFACE ROUGHNESS WITH CNC PLASMA CUTTING ON STEEL PLATES SS400. J Din Vokasional Tek Mesin 2024;09:26–35. https://doi.org/10.21831/dinamika.v9i1.

Agarwal PH. Optimizing Plasma Arc Cutting Parameters for Structural Steel using Grey Relational Analysis. Int J Eng Res Technol 2019;8:27–30.

Dzienniak D. The influence of technological parameters of plasma cutting on the quality and surface roughness when cutting thick steel sheets. Min Mach 2024;42:108–18.

Hang PT, Chau NT, Khang AD. An Investigation on the Effect of Cutting Parameters in CNC Plasma Cutting Process for Carbon Steel Pham. Vietnam J Agric Sci 2021;3:831–42.

Marta AA, Buwono HP, Yudiarto E, Rohman F, Weddakarti E. Prototype Of Laboratory-Scale Plasma Arc For Thin Film Growth And Its Testing. J Polimesin 2024;22:88–92.

Bhowmick S, Basu J, Majumdar G, Bandyopadhyay A. Experimental study of plasma arc cutting of AISI 304 stainless steel. Mater Today Proc 2018;5:4541–50. https://doi.org/10.1016/j.matpr.2017.12.024.

DOI: http://dx.doi.org/10.30811/jpl.v24i2.8618