Effect of electrolyte medium on the tensile strength of coconut coir–epoxy composites via liquid plasma treatment

Sudirman Sudirman; Muh Firdan Nurdin; Marhadi Budi Waluyo; Eva Tri Wulandari; Denal Lebang

doi:10.30811/jpl.v24i1.8614

Effect of electrolyte medium on the tensile strength of coconut coir–epoxy composites via liquid plasma treatment

Sudirman Sudirman, Muh Firdan Nurdin, Marhadi Budi Waluyo, Eva Tri Wulandari, Denal Lebang

Abstract

The application of coconut coir in polymer composites is often restricted by poor interfacial adhesion due to the fiber’s hydrophilic nature. This study investigates the enhancement of tensile strength in coconut coir–epoxy composites via microwave-induced liquid plasma treatment with an electrolyte medium. The experiment employed a randomized design with four fiber treatment groups: untreated (control), plasma-treated in distilled water, plasma-treated in 10% NaCl, and plasma-treated in 10% NaOH. The plasma process was conducted at 400 W for 5 minutes under vacuum conditions (60–70 cmHg). Tensile test results indicate that the electrolyte medium significantly influences the treatment effectiveness. Plasma treatment in a 10% NaOH medium achieved the highest average tensile strength (5.70 MPa), corresponding to a 9.2% improvement over untreated fibers. In contrast, plasma treatment in distilled water resulted in a 21.6% reduction in tensile strength (4.08 MPa). The observed enhancement in the alkaline medium is likely related to combined chemical and physical effects induced by the plasma environment, which may contribute to improved fiber–matrix mechanical interlocking. These findings demonstrate that selecting a conductive, alkaline electrolyte medium is critical for optimizing liquid plasma treatment of natural fibers for composite applications.

Keywords

Coconut coir composite, tensile strength, liquid plasma, alkali treatment, interfacial adhesion.

Full Text:

PDF

References

M. Sood and G. Dwivedi, “Effect of fiber treatment on flexural properties of natural fiber reinforced composites: A review,” Egypt. J. Pet., vol. 27, no. 4, pp. 775–783, Dec. 2018, doi: 10.1016/j.ejpe.2017.11.005.

I. Mawardi, A. Azwar, and A. Rizal, “Kajian perlakuan serat sabut kelapa terhadap sifat mekanis komposit epoksi serat sabut kelapa,” J. Polimesin, vol. 15, no. 1, p. 22, Feb. 2017, doi: 10.30811/jpl.v15i1.369.

S. Junus et al., “Tensile and morphological properties of carbon-coir fiber reinforced epoxy hybrid composites,” J. Polimesin, vol. 23, no. 1, p. 47, Feb. 2025, doi: 10.30811/jpl.v23i1.5523.

Zulkifli, I. B. Dharmawan, and W. Anhar, “Analisa pengaruh perlakuan kimia pada serat terhadap kekuatan impak charpy komposit serat sabut kelapa bermatriks epoxy Effect of chemical treatment of composite coir fiber with epoxy matrix on the Charpy impact strength,” J. Polimesin, vol. 18, no. 1, pp. 47–52, 2020, doi: 10.30811/jpl.v18i1.1583.

D. A. Farrel, Yuliyanto, and Zulfitriyanto, “Pengaruh sifat mekanik komposit serat sabut kelapa bermatrik polyester terhadap pengujian tarik,” J. Indones. Sos. Teknol., vol. 3, no. 2, pp. 219–230, 2022, doi: https://doi.org/10.59141/jist.v3i02.360.

N. H. Sari and J. Fajrin, “Sifat mekanik dari komposit poliester-serat pelepah kelapa: Efek perendaman serat dalam larutan kimia alkali,” J. Tek. Mesin, vol. 7, no. 2, p. 57, Oct. 2018, doi: 10.22441/jtm.v7i2.2373.

H. Hestiawan, D. Ariawan, K. Amri, A. Nuramal, A. Afrizal, and S. Sudibyo, “Pengaruh perlakuan alkali terhadap sifat fisis dan mekanis serat lantung (artocarpus elasticus),” J. Rekayasa Mesin, vol. 13, no. 3, pp. 819–826, Dec. 2022, doi: 10.21776/jrm.v13i3.1220.

P. Valášek, M. Müller, and V. Šleger, “Influence of plasma treatment on mechanical properties of cellulose-based fibres and their interfacial interaction in composite systems,” BioResources, vol. 12, no. 3, pp. 5449–5461, Jun. 2017, doi: 10.15376/biores.12.3.5449-5461.

A. Pavlovic, L. Valzania, and G. Minak, “Effects of moisture absorption on the mechanical and fatigue properties of natural fiber composites: A review,” Polymers (Basel)., vol. 17, no. 14, p. 1996, Jul. 2025, doi: 10.3390/polym17141996.

R. R. Pillai and V. Thomas, “Plasma surface engineering of natural and sustainable polymeric derivatives and their Potential Applications,” Polymers (Basel)., vol. 15, no. 2, p. 400, Jan. 2023, doi: 10.3390/polym15020400.

D. K. Bisoyi, R. Das, and C. Dash, “A Review of cold plasma treatment on textile fibre,” Trends Text. Eng. Fash. Technol., vol. 7, no. 5, pp. 4–6, Jan. 2023, doi: 10.31031/TTEFT.2023.07.000675.

U. S. Gupta et al., “Plasma modification of natural fiber: A review,” Mater. Today Proc., vol. 43, pp. 451–457, 2021, doi: 10.1016/j.matpr.2020.11.973.

A. E. E. Putra, I. Renreng, H. Arsyad, and B. Bakri, “Investigating the effects of liquid-plasma treatment on tensile strength of coir fibers and interfacial fiber-matrix adhesion of composites,” Compos. Part B Eng., vol. 183, no. December 2019, p. 107722, Feb. 2020, doi: 10.1016/j.compositesb.2019.107722.

S. Kocaman, M. Karaman, M. Gursoy, and G. Ahmetli, “Chemical and plasma surface modification of lignocellulose coconut waste for the preparation of advanced biobased composite materials,” Carbohydr. Polym., vol. 159, pp. 48–57, Mar. 2017, doi: 10.1016/j.carbpol.2016.12.016.

Z. Al Mahmud et al., “The mechanical and microstructure investigations of jute fabric epoxy reinforced with microfibers from banana and coconut,” SPE Polym., vol. 5, no. 4, pp. 693–708, Oct. 2024, doi: 10.1002/pls2.10154.

A. Aminur, J. S. D. Saputra, and C. Y. Syah, “Analysis of tensile and bending strength of coconut fiber reinforcement composite on quasi isotropic laminates stacking sequence,” J. Metall. Eng. Process. Technol., vol. 4, no. 2, p. 67, Feb. 2024, doi: 10.31315/jmept.v4i2.11350.

T. P. Kasih and J. Nasution, “Pengembangan teknologi plasma dingin untuk modifikasi karakteristik permukaan material tanpa mengubah sifat dasar material,” vol. 32, no. 3, pp. 167–186, 2021, [Online]. Available: https://publikasi.mercubuana.ac.id/index.php/pasti/article/view/1720/1319

I. Renreng, B. Bakri, S. Chandrabakty, and Naharuddin, “Evaluation of mechanical and physical properties of pressed coir fiber/epoxy composite with NaOH and microwave treatment of fiber,” J. Renew. Mater., vol. 9, no. 2, pp. 325–335, 2021, doi: 10.32604/jrm.2021.012774.

DOI: http://dx.doi.org/10.30811/jpl.v24i1.8614