Investigation on hardness and microstructural behavior of mahogany–brass reinforced bio-composite brake pads under varying compaction pressure

Fatkhurrohman Fatkhurrohman; Rizqa Ruviana; Musyaroh Musyaroh; Anisah Nurul Izzah

doi:10.30811/jpl.v24i2.8593

Investigation on hardness and microstructural behavior of mahogany–brass reinforced bio-composite brake pads under varying compaction pressure

Fatkhurrohman Fatkhurrohman, Rizqa Ruviana, Musyaroh Musyaroh, Anisah Nurul Izzah

Abstract

The gradual elimination of asbestos in brake pad manufacturing has intensified the search for sustainable and non-toxic friction materials. This study presents waste-based bio-composite brake pads reinforced with mahogany sawdust and brass shavings, fabricated using a compaction-sintering approach. The scientific novelty of this study lies in the combined influence of reinforcement composition and compaction pressure on the microstructure-hardness relationship of wood-metal hybrid composites for brake pad applications. The effects of varying mahogany-to-brass ratio and compaction pressure on Shore D hardness and morphological characteristics were systematically evaluated. The results showed that increasing compaction pressure and reinforcement proportion improved composite densification and interfacial bonding, thereby increasing hardness. Increased hardness indicates better structural integrity and load-bearing capacity, which are important mechanical requirements for brake pad materials. The highest hardness value of 76.6 Shore D was obtained at a pressure of 3400 psi with a 4:4 composition, while the lowest value of 70.6 Shore D occurred at 3000 psi with a 1:4 ratio. These findings highlight the role of controlled compaction and balanced hybrid reinforcement in tailoring the mechanical characteristics of sustainable brake pad composites, supporting the potential utilization of wood and metal waste as environmentally friendly friction material components.

Keywords

Hardness Shore D; Bio-composite brake pad; Mahogany sawdust; Brass shavings; Compaction-sintering

Full Text:

PDF

References

Z. Abdullah, P. M. Heerwan, M. A. Zakaria, and M. I. Ishak, “Investigation of Brake Pad Wear Impact on Autonomous Emergency Braking Pedestrian Performance on Wet Road Conditions,” Int. J. Automot. Mech. Eng., vol. 21, no. 2, pp. 11415–11425, 2024.

Y. Wei and J. Yin, “Defect Detection in Disc Brake Pads Using an Improved AlexNet Convolutional Neural Network,” Int. J. Automot. Mech. Eng., vol. 22, no. 3, pp. 12654–12664, 2025.

A. P. Irawan et al., “Overview of the Important Factors Influencing the Performance of Eco-Friendly Brake Pads,” Polymers (Basel)., vol. 14, no. 6, 2022.

L. I. D. Tamás, O. Péter, S. Matyas, S. Erno, S. Alexandros, “Brake Disc Deformation Detection Using Intuitive Feature,” Machines, vol. 214, no. 12, pp. 1–21, 2024.

M. Khafidh et al., “A Study on Characteristics of Brake Pad Composite Materials by Varying the Composition of Epoxy, Rice Husk, Al2O3 and Fe2O3,” Automot. Exp., vol. 6, no. 2, pp. 303–319, 2023.

J. Cao, J. Bao, Y. Yin, W. Yao, T. Liu, and T. Cao, “Intelligent prediction of wear life of automobile brake pad based on braking conditions,” Ind. Lubr. Tribol., vol. 2, no. November, pp. 157–165, 2025.

A. Suraya et al., “Asbestos-related lung cancer: A hospital-based case-control study in Indonesia,” Int. J. Environ. Res. Public Health, vol. 17, no. 2, 2020.

S. Klebe, J. Leigh, D. W. Henderson, and M. Nurminen, “Asbestos , Smoking and Lung Cancer : An Update,” Int. J. Enviromental Res. Public Heal., vol. 258, no. 17, pp. 1–23, 2020.

J. O. Dirisu, I. P. Okokpujie, O. O. Joseph, and S. O. Oyedepo, “Sustainable Biocomposites Materials for Automotive Brake Pad Application : An Overview,” J. Renew. Mater., vol. 12, no. 3, pp. 485–511, 2024.

A. Karimah et al., “A review on natural fibers for development of eco-friendly bio-composite: characteristics, and utilizations,” J. Mater. Res. Technol., vol. 13, pp. 2442–2458, 2021.

C. Feron, G. Nanlohy, T. Sahusilawane, and M. C. Siahay, “Pengaruh Serbuk Kayu Mahoni Sebagai Pengganti Sebagian Agregat Halus Terhadap Kuat Tekan Beton,” J. Penelit. Multidisiplin Bangsa, vol. 1, no. 7, pp. 810–819, 2024.

T. M. Palian, F. Phengkarsa, and L. Buarlele, “Pengaruh Limbah Serbuk Kayu Mahoni Sebagai Subtitusi Agregat Halus Sebagai Campuran Beton,” Paulus Civ. Eng. J., vol. 5, no. 1, pp. 57–67, 2023.

R. Ariawan et al., “Pelatihan Pengolahan Limbah Kayu Mahoni ( Swietenia Mahagoni ) Pada BUMDes Banjarwaru,” J. Commuinity Dev., vol. 5, no. 2, pp. 281–288, 2024.

H. Yilmaz Atay, G. Uslu, Y. Kahmaz, and Atay, “Investigations of microstructure and mechanical properties of brass alloys produced by sand casting method at different casting temperatures,” IOP Conf. Ser. Mater. Sci. Eng., vol. 726, no. 1, 2020.

S. Xu et al., “Effect of sulfate-reducing bacteria on corrosion of copper and brass,” Trans. Nonferrous Met. Soc. China, vol. 35, no. 6, pp. 1919–1936, 2025.

J. Zhao et al., “Effect of cocopeat and brass powder composition as a filler on wear resistance properties,” IOP Conf. Ser. Mater. Sci. Eng., vol. 725, p. 012041, 2020.

Z. Ammar, H. Ibrahim, M. Adly, and I. Sarris, “Influence of Natural Fiber Content on the Frictional Material of Brake Pads — A Review,” J. Compos. Sci., vol. 7, no. 2, p. 72, 2023.

M. A. Essam, N. M. Abdeltawab, A. Y. Shash, and M. M. El-sayed, “Investigation of mechanical properties and performance of automotive brake pads,” Nat. Sci. Reports, vol. 15, no. 32218, pp. 1–16, 2025.

R. Rajan, Y. K. Tyagi, A. Das, P. Kumar, and S. Kumar Patel, “Development and analysis of friction characteristics of coir fiber added organic brake pad composite,” Mater. Today Proc., vol. 62, no. P10, pp. 6077–6082, 2022.

S. Pujari and S. Srikiran, “Experimental investigations on wear properties of Palm kernel reinforced composites for brake pad applications,” Def. Technol., vol. 15, no. 3, pp. 295–299, 2019.

M. Yigrem, O. Fatoba, and S. Tensay, “Tribological and mechanical properties of banana peel hybrid composite for brake-pad application,” Mater. Today Proc., vol. 62, pp. 2829–2838, 2022.

M. C. Wicaksana, Xander Salahudin, and Fuad Hilmy, “Studi Pemanfaatan Campuran Serbuk Tempurung Kelapa dan Serat Bambu untuk Material Alternatif Kampas Rem Sepeda Motor,” Mars J. Tek. Mesin, Ind. Elektro dan Ilmu Komput., vol. 3, no. September, pp. 90–102, 2025.

O. R. Adetunji, A. M. Adedayo, S. O. Ismailia, and O. U. Dairo, “Effect of silica on the mechanical properties of palm kernel shell based automotive brake pad,” Mech. Eng. Soc. Ind., vol. 2, no. 1, pp. 7–16, 2022.

S. M. T. S.H. Thauri, B.T.H.T Baharudin, Z. Leman, “The viability of microwave sintering process to produce a ceramic tool insert,” Int. J. Automot. Mech. Eng., vol. 13, no. 2, pp. 3462–3475, 2016.

J. Ju et al., “Effects of Sintering Pressure and Co Content on the Microstructure and Mechanical Performance of WC – Co Cemented Carbides,” Metals (Basel)., vol. 15, no. 930, pp. 1–14, 2025.

M. Liyong, Z. Ziyong, M. Bao, and W. Min, “Effect of Pressure and Temperature on Densification in Electric Field-Assisted Sintering of Inconel 718 Superalloy,” Materials (Basel)., vol. 14, no. 2546, pp. 1–17, 2021.

Z. Muthia and C. Abdul, “ANALISIS PENGARUH VARIASI TEMPERATUR SINTERING TERHADAP SIFAT MEKANIK PADUAN Fe–Al DAN SiO₂ SEBAGAI BAHAN ALTERNATIF BUSI MOTOR,” J. MESIN Inov. DAN Teknol., vol. 5, no. 2, pp. 53–61, 2025.

I. F. Fakhrurrozi, M. K. Herliansyah, and K. Kusmono, “Characterization and mechanical properties of PLA / acetylated cellulose nanocrystals composites for dental crown prototype application,” Results Eng., vol. 25, p. 103903, 2025.

American Society for Testing and Materials, “ASTM D2240-15 Standard Test Methods for Rubber Property-Durometer Hardness,” Annu. B. ASTM Stand., pp. 1–13, 2015.

P. A. Palacios, A. Velazquez, R. Zelaya, and A. E. Patterson, “Shore hardness of as-printed and dehydrated thermoplastic materials made using fused filament fabrication (FFF),” Mater. Today Commun., vol. 35, no. January, p. 105971, 2023.

H. S. Fadhil and R. S. Hadi, “EROSION WEAR AND HARDNESS SHORE D OF EPOXY,” Iraqi J. Mech. Mater. Eng., vol. 21, no. 1, pp. 26–34, 2021.

DOI: http://dx.doi.org/10.30811/jpl.v24i2.8593