Improvement of mechanical properties of aluminium matrix composites through addition of alumina by stir casting method

Nur Kholis, Sri Mulyo Bondan Respati, Evan Chahya Kurniawan

Abstract


Aluminum is a material widely used in various industries. Aluminum has superior properties, one of which is corrosion resistance and good formability. However, one of the disadvantages of aluminum is that it has relatively low strength compared to other materials. Therefore, this study aims to determine the effect of adding various alumina to aluminum metal casting using the stir casting method on physical and mechanical properties. In this research, aluminum waste was used as the main matrix, and alumina powder (Al2O3) was used as reinforcing particles with weight fractions of 15%, 20%, and 25%. The material was melted at a temperature of 800 °C and a stirring speed of 500 Rpm for 5 minutes. Macro and micro observations were conducted using an optical metallography instrument. Mechanical testing included hardness testing using a Rockwell Hardness scale B instrument and tensile testing using a Universal Testing Machine. The test results showed several defects, including porosity, shrinkage, air holes, misruns, flash, and rough surfaces. Porosity and air pockets are usually caused by gas (especially hydrogen in aluminum) that is trapped during cooling due to insufficiently dry moulds or poor ventilation. The microstructure results show that Al2O3 agglomeration is highest at a 25% addition, which occurs because the stirring speed of 500 RPM is not sufficient to evenly distribute the Al2O3 particles. The highest hardness value is still found in the raw material (without reinforcement) at 73.33 HRB, while the material with the highest Al₂O₃ reinforcement at 25% addition has a hardness of 43 HRB. The highest tensile strength value was observed at the 25% alumina reinforcement parameter, with a value of 135.35 HRB, and the lowest at the 15% reinforcement addition, with a value of 128.64. The decrease in both hardness and tensile strength values compared to the raw material is attributed to alumina agglomeration.


Keywords


Aluminium, AMCs, Stir Casting, Al2O3, Tensile Strength

Full Text:

PDF

References


N. Kholis, H. Purwanto, and A. Adib, “Optimization of process parameters for making alumina reinforced recycled aluminum composites using the stir casting method,†vol. 11, no. 2, pp. 1–11, 2023, doi: 10.30738/jtv.v11i2.15904.

B. E. Arendarchuck, A. R. Mayer, L. A. Lourençato, C. R. C. Lima, and H. D. C. Fals, “Assessment of the microstructure and abrasive wear properties of an A380/NbC aluminum composite produced by stir casting,†Int. J. Met., vol. 18, no. 2, pp. 1783–1799, 2024, doi: 10.1007/s40962-023-01154-y.

H. Purwanto, D. Darmanto, N. Kholis, and W. Mufidin, “Pengaruh variasi temperatur tuang pada pengecoran daur ulang al-si terhadap struktur mikro dan kekerasan dengan pola styrofoam,†JMPM (Jurnal Mater. dan Proses Manufaktur), vol. 5, no. 1, pp. 43–51, 2021, doi: 10.18196/jmpm.v5i1.12441.

A. P. Iman Saefuloh and R. Hikmatullah, Matrix Composite ( Amc ) Paduan Al , 5 % Cu ,†vol. 12, no. 2, pp. 151–164, 2018.

B. Widodo and A. Subardi, “Pengujian sifat mekanik dan struktur mikro aluminium matrix composite ( Amc ) Berpenguat Partikel Silikon Karbida ( SiC ) dan Alumina (AL2O3),†Semin. Nas. Inov. dan Apl. Teknol. di Ind. 2019, pp. 295–303, 2019.

S. Wilastri, A. P. Bayuseno, and S. Nugroho, “Pengaruh variasi kecepatan putar dalam metode stir casting terhadap densitas dan porositas Al- SiC untuk aplikasi blok rem kereta api,†Momentum, vol. 7, pp. 31–35, 2011.

P. Chakrapani and T. S. A. Suryakumari, “Mechanical properties of aluminium metal matrix composites-A review,†Mater. Today Proc., vol. 45, no. xxxx, pp. 5960–5964, 2020, doi: 10.1016/j.matpr.2020.09.247.

R. Alfattani and M. Yunus, “Explorations of mechanical and corrosion resistance properties of AA6063/TiB2/Cr2O3 hybrid composites produced by stir casting,†J. Sci. Adv. Mater. Devices, vol. 9, no. 4, p. 100790, 2024, doi: 10.1016/j.jsamd.2024.100790.

A. P. J. Fahmi Azis, Sunardi, “Analisa pengaruh komperesibilitas metalurgi serbuk terhadap karakteristik fisik pada komposit matriks logam alumunium berpenguat alumina,†Pros. Semin. Nas. Energi, Manufaktur, dan Peranc. Tek. Mesin, pp. 1–11, 2012.

D. Yusuf Hendronursito, Cipto Agustam, “Optimasi perlakuan panas dan proses stir casting menggunakan metoda taguchi optimization of heat treatment and stir casting process of al-basalt composite on mechanical properties using,†vol. 10, no. 2, pp. 66–73, 2020, doi: 10.37209/jtbbt.

H. Sukma, R. Prasetyani, D. Rahmalina, and R. Imanuddin, “Peran penguat partikel alumina dan silikon karbida terhadap kekerasan material komposit matriks aluminium,†no. November, pp. 1–13, 2015.

J. Sun et al., “Strength and elastic modulus enhancement in Mg-Li-Al matrix composites reinforced by ex situ TiB2 particles via stir casting,†J. Magnes. Alloy., vol. 12, no. 9, pp. 3574–3588, 2024, doi: 10.1016/j.jma.2022.09.020.

A. Arifin and Junaidi, “Volume III Nomor 1, April 2017 (Amir Arifin, dkk.),†Anal. pengaruh kelembaban sampah kayu dan sisa makanan pada incenerator portable skala rumah tangga, vol. III, no. April, pp. 21–31, 2017.

H. Sukma, D. Rahmalina, E. A. Pane, and A. Gantina, “Pengaruh proses penuaan untuk meningkatkan kekerasan material komposit matriks aluminium,†vol. IV, no. 1, pp. 49–55, 2018.

A. Nur Kholis1, Yudhi Purnama, Helmy Purwanto and R. H. Nugroho, “Physical and mechanical properties of aluminum matrix composites reinforced with copper powder via Stir casting method,†vol. 23, no. 1, pp. 11–16, 2025, doi: http://dx.doi.org/10.30811/jpl.v23i1.5587.

ASTM standard 407-07, “ASTM 407-07, Standard practice for microetching metals and alloys, astm international, west conshohocken, PA, 2007,†pp. 1–21, 2005, doi: 10.1520/E0407-07.2.

ASTM E8, “ASTM E8/E8M standard test methods for tension testing of metallic materials 1,†Annu. B. ASTM Stand. 4, no. C, pp. 1–27, 2010, doi: 10.1520/E0008.

M. Jolly and L. Katgerman, “Modelling of defects in aluminium cast products,†Prog. Mater. Sci., vol. 123, no. August 2020, p. 100824, 2022, doi: 10.1016/j.pmatsci.2021.100824.

A. Thakur, D. Bandhu, D. R. Peshwe, Y. Y. Mahajan, K. K. Saxena, and S. M. Eldin, “Appearance of reinforcement, interfacial product, heterogeneous nucleant and grain refiner of MgAl2O4 in aluminium metal matrix composites,†J. Mater. Res. Technol., vol. 26, pp. 267–302, 2023, doi: 10.1016/j.jmrt.2023.07.121.

B. N. Akash Deep et al., “Ultrasonic assisted stir squeeze casting of AA5456/Al2O3–SiC-Gr-MoS2 hybrid nanocomposites: Microstructure and strengthening analysis,†J. Mater. Res. Technol., vol. 34, no. July 2024, pp. 1611–1635, 2025, doi: 10.1016/j.jmrt.2024.12.172.

V. Bharath, M. Nagaral, V. Auradi, and S. A. Kori, “Preparation of 6061Al-Al 2 O 3 MMC’s by stir casting and evaluation of mechanical and wear properties,†Procedia Mater. Sci., vol. 6, no. Icmpc, pp. 1658–1667, 2014, doi: 10.1016/j.mspro.2014.07.151.




DOI: http://dx.doi.org/10.30811/jpl.v23i4.7376

Refbacks

  • There are currently no refbacks.


Bookmark and Share


Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Lisensi Creative Commons

Ciptaan disebarluaskan di bawah Lisensi Creative Commons Atribusi-BerbagiSerupa 4.0 Internasional .

 

Alamat Surat :

Politeknik Negeri Lhokseumawe
Jl. Banda Aceh-Medan Km 280
Buketrata, Lhokseumawe, 24301, Aceh, Indonesia