Shear strength comparison of single lap and joggle lap adhesive joints in carbon fiber composites manufactured via vacuum-assisted resin infusion

Mikhael Gilang Pribadi Putra Pratama, Kosim Abdurohman, Rezky Agung Pratomo, Ryan Hidayat, Redha Akbar Ramadhan, Rian Suari Aritonang, Taufiq Satrio Nurtiasto, Riki Ardiansyah, Afid Nugroho, Awang Rahmadi Nuranto, Fajar Ari Wandono, Dudi Targani, Nur Mufidatul Ula

Abstract


The extensive utilization of composite materials has spurred the advancement of diverse joining techniques suitable for components constructed from such materials. This study focuses on the examination of two specific types of joints: single lap and joggle lap joints. The specimens utilized were composed of unidirectional carbon fiber composite combined with vinyl ester resin, manufactured via the vacuum-assisted resin infusion method. Vinyl ester adhesives were employed in the bonding process, with the joint surfaces undergoing sanding treatment prior to testing. Mechanical testing was conducted on the specimens according to ASTM D5868 standard, employing a constant crosshead speed until failure occurred. The test results reveal that the shear strength of single lap joints surpasses that of joggle lap joints. Within the single lap joint configuration, a mixed failure mode comprising both adhesive and cohesive failure is observed. Conversely, in joggle lap joints, substrate delamination is prevalent, suggesting the predominance of peel stress during loading.

Keywords


Single lap joint, joggle joint, composite, shear strength.

Full Text:

PDF

References


F. Gnädinger, P. Middendorf, and B. Fox, “Interfacial shear strength studies of experimental carbon fibres, novel thermosetting polyurethane and epoxy matrices and bespoke sizing agents,” Compos SciTechnol, vol. 133, pp. 104–110, 2016, doi: 10.1016/j.compscitech.2016.07.029.

G. Wu, L. Chen, and L. Liu, “Effects of silanization and silica enrichment of carbon fibers on interfacial properties of methylphenylsilicone resin composites,” Compos Part AApplSciManuf, vol. 98, pp. 159–165, 2017, doi: 10.1016/j.compositesa.2017.03.024.

N. K. Yadav, N. S. Rajput, S. Kulshreshtha, and M. K. Gupta, “Investigation of the Mechanical and Wear Properties of Epoxy Resin Composite (ERCs) Made With Nano Particle TiO2 and Cotton Fiber Reinforcement,” Evergreen, vol. 10, no. 1, pp. 63–77, 2023, doi: 10.5109/6781041.

S. Bindu, M. Prasanna Kumar, and K. M. Vinay, “Development and Mechanical Properties Evaluation of Basalt-Glass Hybrid Composites,” Evergreen, vol. 10, no. 3, pp. 1341–1348, 2023, doi: 10.5109/7151681.

D. Choudhari and V. Kakhandki, “Characterization and Analysis of Mechanical Properties of Short Carbon Fiber Reinforced Polyamide66 Composites,” Evergreen, vol. 8, no. 4, pp. 768–776, 2021, doi: 10.5109/4742120.

S. W. Park and D. G. Lee, “Adhesion strength of glass/epoxy composite embedded with heat-treated carbon black on the surface,” Compos Part A ApplSciManuf, vol. 41, no. 11, pp. 1597–1604, 2010, doi: 10.1016/j.compositesa.2010.07.008.

D. S. Patil and M. M. Bhoomkar, “Investigation on Mechanical Behaviour of Fiber-Reinforced Advanced Polymer Composite Materials,” Evergreen, vol. 10, no. 1, pp. 55–62, 2023, doi: 10.5109/6781040.

A. Anggoro Putra, D. TeguhSantoso, and F. ChoriaSuci, “Effect of Volume Fraction of Polyester Composite Reinforced Human Hair Fibers and Coconut Fibers On Mechanical Properties,” vol. 20, no. 2, pp. 143–148, 2022, doi: 10.30811/jpl.v20i2.2935.

B. Istana, F. Alfredo, and S. Sunaryo, “Characterization of the Mechanical Properties of Fiberglass/Epoxy Prepreg Composites as Horizontal Axis Wind Turbine Blade Material: Influence of Fiber Orientation on Impact and Bending Strength,” vol. 22, no. 4, pp. 457–461, 2024, doi: 10.30811/jpl.v22i4.5363.

M. Awi and A. S. Abdullah, “A Review on Mechanical Properties and Response of Fibre Metal Laminate under Impact Loading (Experiment),” Evergreen, vol. 10, no. 1, pp. 111–129, 2023, doi: 10.5109/6781057.

J. H. Kim, P. Lopez-Cruz, M. Heidari-Rarani, L. Lessard, and J. Laliberté, “An experimental study on the mechanical behaviour of bonded and hybrid bonded-bolted composite joints using digital image correlation (DIC) technique,” Compos Struct, vol. 276, no. March, p. 114544, 2021, doi: 10.1016/j.compstruct.2021.114544.

X. Li, Z. Tan, L. Wang, J. Zhang, Z. Xiao, and H. Luo, “Experimental investigations of bolted, adhesively bonded and hybrid bolted/bonded single-lap joints in composite laminates,” Mater Today Commun, vol. 24, no. May, p. 101244, 2020, doi: 10.1016/j.mtcomm.2020.101244.

G. Sinn et al., “Mechanical and fracture mechanical properties of matrix-reinforced carbon fiber composites with carbon nanotubes,” Key Eng Mater, vol. 809 KEM, pp. 615–619, 2019, doi: 10.4028/www.scientific.net/KEM.809.615.

X. Cheng, J. Zhang, J. Bao, B. Zeng, Y. Cheng, and R. Hu, “Low-velocity impact performance and effect factor analysis of scarf-repaired composite laminates,” Int J Impact Eng, vol. 111, pp. 85–93, 2018, doi: 10.1016/j.ijimpeng.2017.09.004.

A. J. Kinloch, Adhesion and Adhesives, no. 1. 1987. [Online]. Available: http://repositorio.unan.edu.ni/2986/1/5624.pdf%0Ahttp://fiskal.kemenkeu.go.id/ejournal%0Ahttp://dx.doi.org/10.1016/j.cirp.2016.06.001%0Ahttp://dx.doi.org/10.1016/j.powtec.2016.12.055%0Ahttps://doi.org/10.1016/j.ijfatigue.2019.02.006%0Ahttps://doi.org/10.1

C. Xiaoquan, Y. Manman, Z. Jie, Z. Qian, and Z. Jikui, “Thermal behavior and tensile properties of composite joints with bonded embedded metal plate under thermal circumstance,” Compos B Eng, vol. 99, pp. 340–347, 2016, doi: 10.1016/j.compositesb.2016.06.041.

C. Barile, C. Casavola, V. Moramarco, C. Pappalettere, and P. K. Vimalathithan, “Bonding characteristics of single-and joggled-lap CFRP specimens: Mechanical and acoustic investigations,” Applied Sciences (Switzerland), vol. 10, no. 5, 2020, doi: 10.3390/app10051782.

X. Wei, H. Wang, and H. S. Shen, “A novel approach for the interfacial stress analysis of composite adhesively bonded joints,” Compos SciTechnol, vol. 184, no. September, p. 107830, 2019, doi: 10.1016/j.compscitech.2019.107830.

P. Yarrington, J. Zhang, C. Collier, and B. A. Bednarcyk, “Failure analysis of adhesively bonded composite joints,” Collection of Technical Papers - AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference, vol. 10, no. April, pp. 6972–6994, 2005, doi: 10.2514/6.2005-2376.

A. NematiGiv, Q. Fu, L. Yan, and B. Kasal, “Interfacial bond strength of epoxy and PUR adhesively bonded timber-concrete composite joints manufactured in dry and wet processes,” Constr Build Mater, vol. 311, no. July, p. 125356, 2021, doi: 10.1016/j.conbuildmat.2021.125356.

S. Omairey, N. Jayasree, and M. Kazilas, “Defects and uncertainties of adhesively bonded composite joints,” SN ApplSci, vol. 3, no. 9, 2021, doi: 10.1007/s42452-021-04753-8.

R. Bhanushali, D. Ayre, and H. Y. Nezhad, “Tensile Response of Adhesively Bonded Composite-to-composite Single-lap Joints in the Presence of Bond Deficiency,” Procedia CIRP, vol. 59, no.TESConf 2016, pp. 139–143, 2017, doi: 10.1016/j.procir.2016.09.021.

M. Roy Choudhury and K. Debnath, “Experimental analysis of tensile and compressive failure load in single-lap adhesive joint of green composites,” Int J AdhesAdhes, vol. 99, no. November 2019, 2020, doi: 10.1016/j.ijadhadh.2020.102557.




DOI: http://dx.doi.org/10.30811/jpl.v22i5.5437

Refbacks

  • There are currently no refbacks.




Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

 

  

    

    

Lisensi Creative Commons

Ciptaan disebarluaskan di bawah Lisensi Creative Commons Atribusi-BerbagiSerupa 4.0 Internasional .

 

Alamat Surat :

Politeknik Negeri Lhokseumawe
Jl. Banda Aceh-Medan Km 280
Buketrata, Lhokseumawe, 24301, Aceh, Indonesia