An investigation into the crashworthiness criteria of a top-hat structure with a dent-type crush initiator through numerical analysis

Harry Purnama

doi:10.30811/jpl.v21i5.4126

An investigation into the crashworthiness criteria of a top-hat structure with a dent-type crush initiator through numerical analysis

Harry Purnama

Abstract

Ensuring the safety of passengers and the battery compartment in electric vehicles during frontal collisions is of utmost importance. This research aims to enhance the design of the top-hat structure used in car front rails by incorporating a crush initiator as the weakest section. The addition of a crush initiator optimizes the crashworthiness criteria by reducing peak force and increasing energy absorption. Numerical simulations were conducted using ABAQUS to validate the findings and compared against experimental results from references. The results demonstrate that the development of a top-hat structure with a dent-type crush initiator led to 27.5% decrease in peak force and 18.75% increase in energy absorption. The improvements in peak force and energy absorption could reduce the impact force and allow the crumple zone to completely absorb the kinetic energy during a collision, positively affecting the safety of passengers and battery compartments in electric vehicles

Keywords

Crashworthiness; Top-hat structure; Crush initiator; Numerical analysis; Electric vehicle

Full Text:

PDF

References

Z. Biqiang, L. Xiaodong, and Z. Yajun, “The structure optimization analysis of electric vehicle in small offset rear end collision,” Procedia Eng., vol. 137, pp. 103–108, 2016.

J. A. Sanguesa, V. Torres-Sanz, P. Garrido, F. J. Martinez, and J. M. Marquez-Barja, “A Review on Electric Vehicles: Technologies and Challenges,” 2021, doi: 10.3390/smartcities4010022.

Q. Q. Li, E. Li, T. Chen, L. Wu, G. Q. Wang, and Z. C. He, “Improve the frontal crashworthiness of vehicle through the design of front rail,” Thin-Walled Struct., vol. 162, p. 107588, 2021, doi: https://doi.org/10.1016/j.tws.2021.107588.

M. D. White and N. Jones, “Experimental study into the energy absorbing characteristics of top-hat and double-hat sections subjected to dynamic axial crushing,” Proc. Inst. Mech. Eng. Part D J. Automob. Eng., vol. 213, no. 3, pp. 259–278, 1999.

F. Schneider and N. Jones, “Impact of thin-walled high-strength steel structural sections,” Proc. Inst. Mech. Eng. Part D J. Automob. Eng., vol. 218, no. 2, pp. 131–158, 2004, doi: 10.1243/095440704772913927.

G. Sun, H. Zhang, J. Fang, G. Li, and Q. Li, “Multi-objective and multi-case reliability-based design optimization for tailor rolled blank (TRB) structures,” Struct. Multidiscip. Optim., vol. 55, pp. 1899–1916, 2017.

L. Duan, Z. Du, H. Jiang, W. Xu, and Z. Li, “Theoretical prediction and crashworthiness optimization of top-hat thin-walled structures under transverse loading,” Thin-Walled Struct., vol. 144, p. 106261, Nov. 2019, doi: 10.1016/J.TWS.2019.106261.

H. Purnama, J. I.-M. I. P. Industri, and undefined 2021, “Analysis Of Spot-Welding Pitch On Top Hat Structure Against Crashworthiness Criteria,” ejurnal.bppt.go.id, vol. 15, no. 1, pp. 28–33, 2021, Accessed: Apr. 09, 2023. [Online]. Available: https://ejurnal.bppt.go.id/index.php/MIPI/article/view/4628

F. Xu and C. Wang, “Dynamic axial crashing of tailor-welded blanks (TWBs) thin-walled structures with top-hat shaped section,” Adv. Eng. Softw., vol. 96, pp. 70–82, 2016.

A. K. Lakshminarayanan and C. J. Daniel, “Influence of friction stir welding variants on crashworthiness of friction stir welded aluminium top hat sections,” Mater. Sci. Forum, vol. 979 MSF, pp. 97–101, 2020, doi: 10.4028/www.scientific.net/MSF.979.97.

Y.-B. Cho, C.-H. Bae, M.-W. Suh, and H.-C. Sin, “A vehicle front frame crash design optimization using hole-type and dent-type crush initiator,” Thin-Walled Struct., vol. 44, no. 4, pp. 415–428, 2006.

M. Ferdynus, M. Kotełko, and M. Urbaniak, “Crashworthiness performance of thin-walled prismatic tubes with corner dents under axial impact-Numerical and experimental study,” Thin-Walled Struct., vol. 144, p. 106239, 2019.

M. Malawat, J. Istiyanto, and D. A. Sumarsono, “Effects of wall thickness and crush initiators position under experimental drop test on square tubes,” in Applied Mechanics and Materials, Trans Tech Publ, 2017, pp. 612–618.

V. Tarigopula, M. Langseth, O. S. Hopperstad, and A. H. Clausen, “Axial crushing of thin-walled high-strength steel sections,” Int. J. Impact Eng., vol. 32, no. 5, pp. 847–882, 2006.

Z. Kazancı and K.-J. Bathe, “Crushing and crashing of tubes with implicit time integration,” Int. J. Impact Eng., vol. 42, pp. 80–88, 2012.

J. Istiyanto, H. Purnama, J. Triwardono, and J. Hendrawan, “The Effect of Corner Radius of Square Thin-Walled Structures on Crashworthiness Indicators,” Maj. Ilm. Pengkaj. Ind., vol. 16, no. 2, pp. 81–86, 2022.

S. Qin, X. Deng, and X. Liu, “Crashworthiness analysis of bioinspired hierarchical gradient multicell tubes under axial impact,” Thin-Walled Struct., vol. 179, p. 109591, 2022.

S. F. Abdulqadir, A. A. Abed, and A. Bassam, “Crashworthiness enhancement of thin-walled hexagonal tubes under flexural loads by using different stiffener geometries,” Mater. Today Proc., vol. 42, pp. 2887–2895, 2021.

E. Roszkowska, “Multi-criteria decision making models by applying the TOPSIS method to crisp and interval data,” Mult. Criteria Decis. Making/University Econ. Katowice, vol. 6, no. 1, pp. 200–230, 2011.

Y. Lamrani Alaoui, Introduction to Multi Criteria Decision Making: TOPSIS Method. 2019. doi: 10.13140/RG.2.2.36465.22882.

A. Dimas, T. Dirgantara, L. Gunawan, A. Jusuf, and I. S. Putra, “The effects of spot weld pitch to the axial crushing characteristics of top-hat crash box,” Appl. Mech. Mater., vol. 660, pp. 578–582, 2014.

A. Jusuf, L. Gunawan, T. Dirgantara, and F. Mubarhak, “Numerical Analysis of Double-Hat Multi-Corner Column Under Axial Loading,” in Advances in Lightweight Materials and Structures: Select Proceedings of ICALMS 2020, Springer, 2020, pp. 31–41.

DOI: http://dx.doi.org/10.30811/jpl.v21i5.4126