Investigation Of Turning Results Using Used Chisel Bit File And Ahisel Bits From ST-37 Steel Pack Carburizing

Hendi Lilih Wijayanto; Alexander Malau; Amiruddin Amiruddin; Aditya Perdana Putra; Muh Alfian

doi:10.30811/jpl.v22i1.3935

Investigation Of Turning Results Using Used Chisel Bit File And Ahisel Bits From ST-37 Steel Pack Carburizing

Hendi Lilih Wijayanto, Alexander Malau, Amiruddin Amiruddin, Aditya Perdana Putra, Muh Alfian

Abstract

Much research in the manufacturing industry has been conducted on variations in cutting force, temperature, and chip directly related to tool wear and cutting performance. Therefore, this research analyzed the cutting performance of cutting tools from the pack carburizing-used files against the results of turning facings. Then, the chisels were welded to ISO 6 tool holders after welding. The chisels were used to turn low carbon steel ST-37 with a diameter of 50.4 mm using a timeway CL-460 lathe with 0.2mm feeding and 400, 605, 910, and 1330 RPM variations. The test results indicated that the bit of carbide from the pack carburizing had a roughness value of 0.890 µm, belonging to class N6. Hence, the roughness value was lower (smoother) than turning facing using a file used from pack carburizing with a roughness value of 3.014 µm.

Keywords

Pack carburizing, ST-37, chisel holder ISO 6.

Full Text:

PDF

References

K. Tsuda, “History of development of cemented carbides and cermet,” SEI Technical Review, no. 82, pp. 16–20, 2016.

I. Y. Konyashin, “Cemented Carbide Tools,” Concise Encyclopedia of Self-Propagating High-Temperature Synthesis: History, Theory, Technology, and Products, pp. 54–55, Jan. 2017, doi: 10.1016/B978-0-12-804173-4.00023-5.

L. Zhang and Q. Chen, CALPHAD-Type Modeling of Diffusion Kinetics in Multicomponent Alloys, 1st ed., vol. 1. Elsevier Inc., 2017. doi: 10.1016/B978-0-12-804287-8.00006-3.

K. Tsuda, “History of development of cemented carbides and cermet,” SEI Technical Review, no. 82, pp. 16–20, 2016.

K. Vasilko, Z. Murcinková, and J. Murcinko, “Evaluation of performance of uncoated cemented carbide cutting tools at longitudinal turning at cutting velocity 3-500 m/min and influence of coating,” Mater Today Proc, vol. 44, pp. 2575–2580, 2021, doi: 10.1016/j.matpr.2020.12.641.

T. Nguyen, P. Kwon, D. Kang, and T. R. Bieler, “The Origin of Flank Wear in Turning Ti-6Al-4V,” Journal of Manufacturing Science and Engineering, Transactions of the ASME, vol. 138, no. 12, 2016, doi: 10.1115/1.4034008.

B M Kumar and M MRatnam, “Study on Effect of Tool Nose Radius Wear on Hybrid Roughness Parameters during Turning Using Vision-Based Approach,” 2019, doi: 10.1088/1757-899X/530/1/012009.

X. Guo, S. Yin, C. Shu, S. Wu, and J. Liu, “Contact on-machine measurement probe error correction method for optical aspheric surface ultraprecision machining,” Measurement, vol. 214, p. 112731, Jun. 2023, doi: 10.1016/J.MEASUREMENT.2023.112731.

P. Pawlus, R. Reizer, and M. Wieczorowski, “Functional Importance of Surface Texture Parameters,” Materials, vol. 14, no. 18, Sep. 2021, doi: 10.3390/MA14185326.

C. Agrawal, J. Wadhwa, A. Pitroda, C. I. Pruncu, M. Sarikaya, and N. Khanna, “Comprehensive analysis of tool wear, tool life, surface roughness, costing and carbon emissions in turning Ti–6Al–4V titanium alloy: Cryogenic versus wet machining,” TribolInt, vol. 153, Jan. 2021, doi: 10.1016/J.TRIBOINT.2020.106597.

B. Arifvianto, Suyitno, M. Mahardika, P. Dewo, P. T. Iswanto, and U. A. Salim, “Effect of surface mechanical attrition treatment (SMAT) on microhardness, surface roughness and wettability of AISI 316L,” Mater Chem Phys, vol. 125, no. 3, pp. 418–426, Feb. 2011, doi: 10.1016/J.MATCHEMPHYS.2010.10.038.

A. H. Astaraee, S. Bagherifard, S. Monti, and M. Guagliano, “Evaluating the Homogeneity of Surface Features Induced by Impact-Based Surface Treatments,” Materials, vol. 14, no. 13, Jul. 2021, doi: 10.3390/MA14133476.

M. Yasir, “TEKNIK KONSTRUKSI DAN MANUFAKTUR “ANALISA KEAUSAN PAHAT KARBIDA SEBELUM MENGGUNAKAN SERBUK ARANG TEMPURUNG,” 2017.

M. Arianto Leman S., Tiwan, “Pahatdaribajakarbonrendah yang dikarburisingpadat (,” no. 1, 2007.

R. R. Abbott, “Steel and its Heat Treatment,” Sci Am, vol. 73, no. 1899supp, pp. 323–323, 1912, doi: 10.1038/scientificamerican05251912-323asupp.

P. Negara and I. M. Widiyarta, “The study on mechanical properties of pack carburized low carbon steel using BaCO3 as energizer”, doi: 10.1088/1757-899X/673/1/012125.

HendiLilihWijayanto, “Perbandingan Pack Carburizing Mata PahatBubutKarbidadan Mata PahatdariKikirBekasPraktikumKerjaBangku,” 2023.

B. Siswanto and S. Sunyoto, “PengaruhKecepatandanKedalamanPotongpada Proses PembubutanKonvensionalTerhadapKekasaranPermukaanLubang,” JurnalDinamikaVokasionalTeknikMesin, vol. 3, no. 2, pp. 82–86, Oct. 2018, doi: 10.21831/DINAMIKA.V3I2.21403.

N. S. Kumar, A. Shetty, A. Shetty, K. Ananth, and H. Shetty, “Effect of Spindle Speed and Feed Rate on Surface Roughness of Carbon Steels in CNC Turning,” ProcediaEng, vol. 38, pp. 691–697, Jan. 2012, doi: 10.1016/J.PROENG.2012.06.087.

N. S. Kumar, A. Shetty, A. Shetty, K. Ananth, and H. Shetty, “Effect of spindle speed and feed rate on surface roughness of carbon steels in CNC turning,” ProcediaEng, vol. 38, no. Icmoc, pp. 691–697, 2012, doi: 10.1016/j.proeng.2012.06.087.

W. Sun, Y. Zhang, M. Luo, Z. Zhang, and D. Zhang, “A multi-criteria decision-making system for selecting cutting parameters in milling process,” J ManufSyst, vol. 65, 2022, doi: 10.1016/j.jmsy.2022.10.008.

G. Kiswanto, M. Azmi, A. Mandala, and T. J. Ko, “The Effect of Machining Parameters to the Surface Roughness in Low Speed Machining Micro-milling Inconel 718,” IOP Conf Ser Mater SciEng, vol. 654, no. 1, 2019, doi: 10.1088/1757-899X/654/1/012014.

DOI: http://dx.doi.org/10.30811/jpl.v22i1.3935