Numerical simulation analysis of structural strength of portable skid for storage tank with 50.000 liter capacity

Muslimin Al Masta

doi:10.30811/jpl.v21i2.3501

Numerical simulation analysis of structural strength of portable skid for storage tank with 50.000 liter capacity

Muslimin Al Masta

Abstract

Abstrack

A storage tank is a container used to store fluids such as fuel, water, and chemical. Skid construction is implemented to make the tank smoothly transported while operated, such as in the mining field. Skids were assembled on the storage tank's base to sit on the ground. This study aims to design and analyze a portable skid storage tank to resist the load of 50,000 liters (392 kN) of fuel and 45 kN of mass of construction itself statically. The skid's main components are a wear plate, pad eye, and seamless pipes of schedule 40 for support, central, and base. All structure's material is 250 MPa yield strength of ASTM 36 low carbon steel. Manual calculations and simulation analysis were implemented to review the skid structure's maximum stress and safety factor. The examination included pipe support, central pipe, and pad eye. Based on the result, the highest stress of 157.88 MPa by ANSYS and 148.07 MPa by manual calculation. Therefore, the construction is safely based on the Tresca and Von Mises criteria.

Keywords

simulation; design; structural strength; portable skid; finite element analysis

Full Text:

PDF

References

B. Winarno, B. Prasojo, And M. M. E. Prayitno, “Desain Dan Pemodelan Pada Storage Tank Kapasitas 50.000 Kl (Studi Kasus Pt.Pertamina Region V Tbbm Tuban),” J. Tek., Pp. 1–4, 2017.

S. Arunkumar, P. R. Eshwara Moorthy, And N. Karthik, “Design Optimization Of Horizontal Pressure Vessel,” Mater. Today Proc., Vol. 26, No. Xxxx, Pp. 1526–1531, 2019, Doi: 10.1016/J.Matpr.2020.02.314.

E. Description, “Chapter 13 Pressure-Volume R Elation,” Changes, Vol. 1, No. 1, Pp. 27–31, 2021

K. Khanna, V. K. Gupta, And S. P. Nigam, “Modelling And Analysis Of Creep In A Variable Thickness Rotating Fgm Disc Using Tresca And Von Mises Criteria,” Iran. J. Sci. Technol. - Trans. Mech. Eng., Vol. 41, No. 2, Pp. 109–119, 2017, Doi: 10.1007/S40997-016-0051-3.

A. Harahap, “Simulasi Pembebanan Pada Shackle Menggunakan Perangkat Lunak Ansys Apdl 15.0,” J. Mech. Eng. Manuf. Mater. Energy, Vol. 4, No. 1, Pp. 74–84, 2020, Doi: 10.31289/Jmemme.V4i1.3811.

S. W. Satoto, M. Fathonah, And A. D. Juli Ardianto, “Studi Perbandingan Desain Geometri Padeye Simetri Dan Tidak Simetri,” J. Integr., Vol. 9, No. 2, P. 97, 2017, Doi: 10.30871/Ji.V9i2.294.

A. Nimade Niraj Soni Assistant Professor, R. Scholar, G. Varma Vikas Joshi, R. Scholar Assistant Professor, And S. Chaurasia Assistant Professor, “Parametric Study Of Underground Water Tank Using Fem,” Ijste-International J. Sci. Technol. Eng. |, Vol. 4, No. 09, Pp. 94–98, 2018, [Online]. Available: Www.Ijste.Org.

B. A. Pedraza-Yepes, J. E. González-Coneo, C. A. Mancera-Trejos, L. E. Florez-Sarmiento, G. Torres-Diaz, And C. González-Olier, “Design And Construction Of Tank-Chassis And Lifting Structure For Centrifugal Pump Hl260 M Powered By A Diesel Engine,” Arpn J. Eng. Appl. Sci., Vol. 15, No. 13, Pp. 1438–1446, 2020.

M. S. Anbazhagan, M. Dev Anand, And G. A. Milton, “Development Of Finite Element Based Wind And Seismic Design Procedure For Horizontal Pressure Vessel,” Procedia Eng., Vol. 38, Pp. 3998–4004, 2012, Doi: 10.1016/J.Proeng.2012.06.457.

H. I. Joshi And G. D. Acharya, “Numerical Investigation Of Design Parameters Influence On Stress Distributions In Horizontal Multi-Saddle Cylindrical Pressure Vessel,” Mater. Today Proc., Vol. 5, No. 9, Pp. 19480–19489, 2018, Doi: 10.1016/J.Matpr.2018.06.309.

Underwriters Laboratories And Ul, Ul 142,2017.

M. Muslimin, A. M. Muhamad, F. Triawan, And A. B. D. Nandiyanto, “Surface Characteristics Of Low Carbon Steel Jisg3101ss400 After Sandblasting Process By Steel Grit G25,” J. Eng. Res., Vol. 10, No. 2 B, Pp. 193–204, 2022, Doi: 10.36909/Jer.10091.

M. Muslimin And A. M. Muhamad, “Penggunaan Steel Grit G25 Pada Sandblasting Baja Karbon Rendah Jis-G3101-SS400,” J. Poli-Teknologi, Vol. 17, No. 3, Pp. 251–258, 2019, Doi: 10.32722/Pt.V17i3.1266

DOI: http://dx.doi.org/10.30811/jpl.v21i2.3501