Effect of nano SiC addition on mechanical properties of Al-Nano SiC composite materials SS304 woven wire using stir casting method

Alfi Hasan, Pieter Muhammad Iko Marrendra, Salahuddin Junus, Mahros Darsin

Abstract


The wide variety of applications in various industries, such as automotive, aerospace, construction, and electronics, aluminum is one of the metals that needs to improve its mechanical properties. This study aims to determine the effect of adding reinforcing powder using the stir casting method on the mechanical properties of the Al-nano SiC/SS304 Wire Woven Composite material. The method used in this study is an experiment with the addition of a matrix to the composite material. The addition of nano metal was carried out to modify the mechanical properties of the aluminum material. Variation of the composition of each specimen using the volume fraction of nano-SiC (1%, 3%, 5%) and 4% Mg and the addition of woven SS304 wire on the tensile strength and hardness tests. The highest tensile test results for the 5% volume fraction variation were 149 MPa and the hardness test was obtained at 69 HRB for the 5% volume fraction variation


Keywords


Aluminium, composite, stir casting, nano-SiC

Full Text:

PDF

References


P. Ajagol, B. N. Anjan, R. N. Marigoudar, and G. V. Preetham Kumar, “Effect of SiC Reinforcement on Microstructure and Mechanical Properties of Aluminum Metal Matrix Composite,†IOP Conf. Ser. Mater. Sci. Eng., vol. 376, no. 1, 2018, doi: 10.1088/1757-899X/376/1/012057.

M. Rahmat and B. D. Haripriadi, “Analisa Pengaruh Variasi Parameter Pemotongan Dan Pendingin Terhadap Tingkat Keausan Pahat End Mill HSS Hasil Pemesinan CNC Router Milling Pada Aluminium Sheet 1100,†J. POLIMESIN, vol. 17, no. 2, pp. 13–20, 2019.

A. Rahmatika, S. Ibrahim, M. Hersaputri, and E. Aprilia, “Studi Pengaruh Variasi Kuat Arus terhadap Sifat Mekanik Hasil Pengelasan GTAW Alumunium 1050 dengan Filler ER 4043,†J. Polimesin, vol. 17, no. 1, pp. 47–54, 2019.

M. Taufiq, “Pengaruh Perlakuan Panas pada Al Alloy 2014 Terhadap Kekuatan Tarik, Keuletan dan Struktur Mikro,†Universitas Muhammadiyah Surakarta, 2020. [Online]. Available: http://eprints.ums.ac.id/id/eprint/90974

D. Permatasari, Z. Zuhaimi, and A. Jannifar, “Analisa Sifat Mekanik Aluminium Alloy 6151 Setelah Mengalami Perlakuan Panas,†J. Mesin Sains Terap., vol. 4, no. 1, p. 1, 2020, doi: 10.30811/jmst.v4i1.1737.

R. T. Loto and P. Babalola, “Corrosion resistance of low SiC particle variation at low weight content on 1060 aluminum matrix composite in sulfate-contaminated seawater,†Results Phys., vol. 13, no. March, p. 102241, 2019, doi: 10.1016/j.rinp.2019.102241.

S. C. Prasanna, C. Ramesh, R. Manivel, and A. Manikandan, “Preparation of Al6061-SiC with Neem Leaf Ash in AMMC’s by Using Stir Casting Method and Evaluation of Mechanical, Wear Properties and Investigation on Microstructures,†Appl. Mech. Mater., vol. 854, pp. 115–120, 2016, doi: 10.4028/www.scientific.net/amm.854.115.

M. Hilman, S. Junus, and I. Hardiatama, “Penambahan Mg Terhadap Sifat Tarik Dan Struktur Mikro Komposit Al-Mg / Anyaman Kawat,†2021.

Suherman, S. Mizhar, and A. Winoto, “Pengaruh Heat Treatment Terhadap Struktur Mikro dan Kekerasan Aluminium Paduan Al-Si-Cu Pada Cylinder Head Sepeda Motor,†MEKANIK, vol. 3, no. 1, pp. 9–15, 2016.

P. Raghuvaran, J. Baskaran, C. Aagash, A. Ganesh, and S. G. Krishna, “Evaluation of mechanical properties of Al7075-SiC composites fabricated through stir casting technique,†Mater. Today Proc., vol. 45, no. xxxx, pp. 1914–1918, 2021, doi: 10.1016/j.matpr.2020.09.191.

S. Awarasang and S. N. S. Awarasan, “Study the Microstructure and Impact Strength of Lm 25 Aluminium Alloy Reinforced With Steel Wire,†Int. Res. J. Eng. Technol., pp. 614–619, 2016, [Online]. Available: www.irjet.net

L. A. N. Wibawa, “Pengaruh diameter baut terhadap kekuatan rangka main landing gear pesawat UAV menggunakan metode elemen hingga,†J. Polimesin, vol. 17, no. 01, pp. 26–32, 2019, [Online]. Available: http://e-jurnal.pnl.ac.id/index.php/polimesin/article/view/828

K. Vishnu Prasad and K. R. Jayadevan, “Simulation of Stirring in Stir Casting,†Procedia Technol., vol. 24, pp. 356–363, 2016, doi: 10.1016/j.protcy.2016.05.048.

W. Jiang, J. Zhu, G. Li, F. Guan, Y. Yu, and Z. Fan, “Enhanced mechanical properties of 6082 aluminum alloy via SiC addition combined with squeeze casting,†J. Mater. Sci. Technol., vol. 88, pp. 119–131, 2021, doi: 10.1016/j.jmst.2021.01.077.

N. K. Maurya, M. Maurya, A. K. Srivastava, S. P. Dwivedi, A. Kumar, and S. Chauhan, “Investigation of mechanical properties of Al 6061/SiC composite prepared through stir casting technique,†Mater. Today Proc., vol. 25, no. xxxx, pp. 755–758, 2019, doi: 10.1016/j.matpr.2019.09.003.

B. Gugulothu, N. Nagarajan, A. Pradeep, G. Saravanan, S. Vijayakumar, and J. Rao, “Analysis of Mechanical Properties for Al-MMC Fabricated through an Optimized Stir Casting Process,†J. Nanomater., vol. 2022, 2022, doi: 10.1155/2022/2081189.

A. A. Adediran, A. A. Akinwande, O. A. Balogun, B. J. Olorunfemi, and S. K. M, “Optimization studies of stir casting parameters and mechanical properties of TiO2 reinforced Al 7075 composite using response surface methodology,†Nature Publishing Group UK, 2021. doi: 10.1038/s41598-021-99168-1.

ASTM E10, “Standard Test Method for Brinell Hardness of Metallic Materials 1,†no. June, 2015, doi: 10.1520/E0010-15.

S. Lutfi, “Pengaruh Mg Terhadap Proses Electroless Coating Pada Partikel Penguat SiC,†Universitas Indonesia, 2010.

S. S. Mohamed, S. A. Abdallah, and H. K.h.Alazemi, “An investigation on the mechanical properties of hybrid metal matrix composites,†Procedia Eng., vol. 97, no. 3, pp. 918–924, 2018, doi: 10.1016/j.proeng.2014.12.367.

Suyanto, Sulardjaka, and S. Nugroho, “Pengaruh Komposisi Mg Dan Sic Terhadap Sifat Kekerasan Komposit AlSi-Sic Yang Dibuat Dengan Proses Semi Solid Stir Casting,†pp. 165–172, 2014.

J. J. Moses, I. Dinaharan, and S. J. Sekhar, “Characterization of Silicon Carbide Particulate Reinforced AA6061 Aluminum Alloy Composites Produced via Stir Casting,†Procedia Mater. Sci., vol. 5, pp. 106–112, 2014, doi: 10.1016/j.mspro.2014.07.247.




DOI: http://dx.doi.org/10.30811/jpl.v21i4.3494

Refbacks

  • There are currently no refbacks.


Bookmark and Share


Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Lisensi Creative Commons

Ciptaan disebarluaskan di bawah Lisensi Creative Commons Atribusi-BerbagiSerupa 4.0 Internasional .

 

Alamat Surat :

Politeknik Negeri Lhokseumawe
Jl. Banda Aceh-Medan Km 280
Buketrata, Lhokseumawe, 24301, Aceh, Indonesia