Studi analisis simulasi kekuatan beban pada alat bantu pembuatan lubang  dengan sudut kemiringan 45 derajat

Dr. Fatahul Arifin, S.T., Dipl.Eng.EPD., M.Eng.Sc; Dwi Arnoldi, S.T., M.T.; Ella Sundari, S.T., M.T.; Fenoria Putri, S.T., M.T.; Feby Agasa; Yudha Ramadhan; Gustaf Susetyo; Dr. Yusuf Dewantoro Herlambang, S.T., M.T.

doi:10.30811/jpl.v18i2.1837

Studi analisis simulasi kekuatan beban pada alat bantu pembuatan lubang dengan sudut kemiringan 45 derajat

Dr. Fatahul Arifin, S.T., Dipl.Eng.EPD., M.Eng.Sc, Dwi Arnoldi, S.T., M.T., Ella Sundari, S.T., M.T., Fenoria Putri, S.T., M.T., Feby Agasa, Yudha Ramadhan, Gustaf Susetyo, Dr. Yusuf Dewantoro Herlambang, S.T., M.T.

Abstract

Jig and Fixture 45 degree bore is a tool which is used to make hole the degree 45 degrees. The goal of study is design and analyze the strength of the frame and assembly with variations in position of load and value from 100 kg to 500 kg. The results of the stress analysis feature with finite element Analysis (FEA) are von misses stress, displacement, and safety factor. The Frame uses a hollow carbon steel of 20 mm x 20 mm, a material of carbon steel. The frame length is 300 mm, the width is 300 mm, the height is 270 mm, dimension of the tool is 300 mm x 300mm x 270 mm. The simulation results are; the safety factor of frame maximum is 7.08 with a load of 100 kg, while minimum is 1.42 with load 500 kg. Whereas, the overall assembly safety factor maximum is 3.88 with loads 100 kg and minimum is 0.82 with load 500 kg. The unsafe location is on the upper of connection frame, while for the overall assembly is on the buffer of shaft component.

Keywords

Jig and Fixture, frame, von misses stress, displacement, safety factor.

Full Text:

PDF (Bahasa Indonesia)

References

Sigijateng. 2019. “Tingkatkan Kesejahtera an Masyarakat dengan Inovasi dan Kreatifitas”. Internet: https://sigijateng.id/2019/ tingka tkan-kesejahteraan-masyarakat-dengan–inovasi-dan-kreatifitas/, April 25, 2020.

Venkataraman K., Design of Jigs, Fixtures and Press Tools, John Wiley & Sons Ltd, West Sussex, United Kingdom, 2015

…., “Bahaya Getaran Pada Alat Kerja, Pekerja Berisiko Terkena Hand-Arm Vibration Syndrome”, https://www.safetysign.co.id/news/283/ Bahaya-Getaran-Pada-Alat-Kerja-Pekerja-Berisiko Terkena Hand-Arm-Vibration-Syndrome, Juli 02, 2020

Hady, E., “Jig and Fixture” https:// www.kompasiana.com/1991/55008c1aa3331130725112d6/jig-dan-fixture, Juni 26, 2015 [Juli 02, 2020]

B. Setyono, dan S. Gunawan, Perancangan dan Analisis Chassis Mobil Listrik “Semut Abang” Menggunakan Software Autodesk Inventor Pro 2013, Seminar Nasional Sains dan Teknologi Terapan III, 2015, ISBN 978-602-98569-1-0. 2015, hal. 69-78

Marcielo D., Anton, Irawan A. P.,“Perancangan Dan Analisis Kekuatan Konstruksi Dan Powertrain Pada Prototype Hand-Crank Cycle (Sepeda Engkol Tangan)”, Jurnal Kajian Teknologi, Vol. 11. No. 1, 2015

Medi, A. dan Rizal, S., “Desain Optimasi Sudut Kipas Sentrifugal”, Jurnal Austenit, Vol. 7, No. 2, ISSN : 2085-1286, 2015

…..,“Computer-aided design”, https:// en.wikipedia.org/wiki/Computer-aided_design, [Juli 02,2020]

M. W. Wang, C. H. Chen, F. Arifin, and J.J Lin, “Modeling and analysis of multi-shot injection molding of Blu-ray objective lens”, Journal of Mechanical Science and Technology vol. 32 ed.10 hal. 4839~4849, DOI 10.1007/s12206-018-0932-z, Jun. 2018

Hasbullah, H., Kholil, M., Santoso, D. A., “Analisis Kegagalan Proses Insulasi Pada Produksi Automotive Wires (Aw) Dengan Metode Failure Mode And Effect Analysis (Fmea) Pada Pt Jlc”, Jurnal Sinergi Vol. 21, No.3, hal. 193-203, DOI:doi.org/10.22441/sinergi.2017.3.006, Oktober 2017

G.R. Liu, and S.S. Quek. Finite Element Method:A Practical Course. Butterworth: Heinemann, Jordan Hill. 2003.

B. Huke, Baker. 1999. ASM Specialty Handbook: Magnesium and Magnesium Alloys. ASM International. Handbook Committee.

Dobrovolsky, dkk. Machine Element. Moscow: MIR Publishers. 1974.

DOI: http://dx.doi.org/10.30811/jpl.v18i2.1837